Er:YAG laser may adversely affect bond strength in higher or lesser degree, depending on the adhesive system used.

The use of Er:YAG laser for cavity preparation and surface treatment negatively influenced the marginal sealing of composite resin restorations.

Er:YAG laser influenced the adhesive systems interface, hampering hybrid layer formation.

Purpose:The aim of this study was to evaluate the surface hardness of six composite resins: Revolution, Natural Flow, Fill Magic Flow, Flow-it! (flowables), Silux Plus (microfilled) and Z100 (minifilled) before and after polishing at different times.Materials and Methods:For this purpose, 240 specimens (5mm diameter, 1.4mm high) were prepared. Vickers hardness was determined before and after polishing at different times: immediately, 24h, 7 and 21 days after preparation of the samples. Statistical analysis was performed by ANOVA and Tukey test.Results:There was no difference in the hardness of flowable resins, which had lower hardness than the minifilled resin. The minifilled resin showed the highest surface hardness as compared to the other materials (p<0.01). All materials exhibited higher hardness after polishing, being more evident after 7 days.Conclusion:It may be concluded that, regardless of the composite resin, surface hardness was considerably increased when polishing was delayed and performed 1 week after preparation of the samples.

This research evaluated the effects of Brånemark protocol on electromyography of the masseter and temporal muscles. The patients were divided into two groups: Group I: patients who wore an implant-supported prosthesis in the mandibular arch following Brånemark protocol, and maxillary removable complete dentures; Group II: dentate individuals (control). Electromyography was carried out at rest, right (RL) and left (LL) laterality, protrusion and maximum voluntary contraction (MVC). Data were compared by t-test. At rest, a higher electromyographic (EMG) activity was observed in Group I, and the values were significant in the right masseter and left temporal muscles. In RL, there were statistically significant differences for right masseter (P < 0·01), left masseter and temporal muscles and for the left temporal muscle in LL (P < 0·05). In protrusion, Group I presented a higher EMG activity, and there was a statistically significant difference for the right masseter muscle (RM) (P < 0·05). In MVC, the EMG values were higher in Group II (control), but significant just for the right temporal muscle (P < 0·05). In conclusion, individuals with mandibular fixed dentures supported according to the Brånemark protocol and maxillary removable complete dentures showed a higher activity of masticatory muscles during the mandibular postural clinical conditions examined; however, in the MVC, Group I presented lower values when compared to dentate group. Despite presenting different EMG values in all of the clinical conditions, both groups showed similar EMG patterns of muscle activation which demonstrates that the proposed treatment can be considered as a good option for oral rehabilitation.

Low-level laser irradiation (LLLI) and recombinant human bone morphogenetic protein type 2 (rhBMP-2) have been used to stimulate bone formation. LLLI stimulates proliferation of osteoblast precursor cells and cell differentiation and rhBMP-2 recruits osteoprogenitor cells to the bone healing area. This in vivo study evaluated the effects of LLLI and rhBMP-2 on the bone healing process in rats. Critical bone defects were created in the parietal bone in 42 animals, and the animals were divided into six treatment groups: (1) laser, (2) 7 μg of rhBMP-2, (3) laser and 7 μg of rhBMP-2, (4) 7 μg of rhBMP-2/monoolein gel, (5) laser and 7 μg rhBMP-2/ monoolein gel, and (6) critical bone defect controls. A gallium-aluminum-arsenide diode laser was used (wavelength 780 nm, output power 60 mW, beam area 0.04 cm 2 , irradiation time 80 s, energy density 120 J/cm 2 , irradiance 1.5 W/cm 2 ). After 15 days, the calvarial tissues were removed for histomorphometric analysis. Group 3 defects showed higher amounts of newly formed bone (37.89%) than the defects of all the other groups (P<0.05). The amounts of new bone in defects of groups 1 and 4 were not significantly different from each other (24.00% and 24.75%, respectively), but were significantly different from the amounts in the other groups (P<0.05). The amounts of new bone in the defects of groups 2 and 5 were not significantly different from each other (31.42% and 31.96%, respectively), but were significantly different from the amounts in the other groups (P<0.05). Group 6 defects had 14.10% new bone formation, and this was significantly different from the amounts in the other groups (P<0.05). It can be concluded that LLLI administered during surgery effectively accelerated healing of critical bone defects filled with pure rhBMP-2, achieving a better result than LLLI alone or the use of rhBMP-2 alone.

LLLT influenced the behavior of odontoblast-like cells; the shorter time/smallest energy density promoted the expression of odontoblastic phenotype in a more significant way.

The aim of this work was to compare the in vitro wear and roughness of different composite resins after toothbrushing. Six resins were tested: Revolution (Kerr), Natural Flow (DFL), Flow It! (Jeneric-Pentron), Fill Magic Flow (Vigodent) -flowable composites, Silux Plus (3M) -microfilled composite, and Z100 (3M) -hybrid composite. Eight disks were prepared for each group (n = 48), with 12 mm in diameter and 1mm thick. The specimens were stored in distilled water at 37 °C for 7 days, polished (Super Snap), weighed and submitted to the initial roughness test. Each sample was fixed on plexiglass plates and subjected to simulated toothbrushing. After abrasion, the samples were removed from the plates, weighed and submitted to the post-abrasion roughness test. Statistical analysis was performed by using ANOVA and Tukey's test. Pearson's test was used to verify correlation between wear and roughness. Data showed a similar resistance to wear of Natural Flow and Z100, both presenting minimum mass loss and surface roughness. Silux Plus presented the roughest surface after toothbrushing.