Fuels of the furan family, i.e. furan itself, 2-methylfuran (MF), and 2,5-dimethylfuran (DMF) are being proposed as alternatives to hydrocarbon fuels and are potentially accessible from cellulosic biomass. While some experiments and modeling results are becoming available for each of these fuels, a comprehensive experimental and modeling analysis of the three fuels under the same conditions, simulated using the same chemical reaction model, has -to the best of our knowledge -not been attempted before. The present series of three papers, detailing the results obtained in flat flames for each of the three fuels separately, reports experimental data and explores their combustion chemistry using kinetic modeling. The first part of this series focuses on the chemistry of low-pressure furan flames. Two laminar premixed low-pressure (20 and 40 mbar) flat argondiluted (50%) flames of furan were studied at two equivalence ratios (φ=1.0 and 1.7) using an analytical combination of high-resolution electron-ionization molecular-beam mass spectrometry (EI-MBMS) in Bielefeld and gas chromatography (GC) in Nancy. The time-of-flight MBMS with its high mass resolution enables the detection of both stable and reactive species, while the gas chromatograph permits the separation of isomers. Mole fractions of reactants, products, and stable and radical intermediates were measured as a function of the distance to the burner. A single kinetic model was used to predict the flame structure of the three fuels: furan (in this paper), 2-methylfuran (in Part II), and 2,5-dimethylfuran (in Part III). A refined sub-mechanism for furan combustion, based on the work of Tian et al. [Combustion and Flame 158 (2011) 756-773] was developed which was then compared to the present experimental results. Overall, the agreement is encouraging. The main reaction pathways involved in furan combustion were delineated computing the rates of formation and consumption of all species. It is seen that the predominant furan consumption pathway is initiated by H-addition on the carbon atom neighboring the O-atom with acetylene as one of the dominant products.

This work is the third part of a study focusing on the combustion chemistry and flame structure of furan and selected alkylated derivatives, i.e. furan in Part I, 2-methylfuran (MF) in Part II, and 2,5-dimethylfuran (DMF) in the present work. Two premixed low-pressure (20 and 40 mbar) flat argon-diluted (50%) flames of DMF were studied with electron-ionization molecular-beam mass spectrometry (EI-MBMS) and gas chromatography (GC) under two equivalence ratios (φ=1.0 and 1.7). Mole fractions of reactants, products, and stable and radical intermediates were measured as a function of the distance to the burner. Kinetic modeling was performed using a reaction mechanism that was further developed in the present series, including Part I and Part II. A reasonable agreement between the present experimental results and the simulation is observed. The main reaction pathways of DMF consumption were derived from a reaction flow analysis. Also, a comparison of the key features for the three flames is presented, as well as a comparison between these flames of furanic compounds and those of other fuels. An a priori surprising ability of DMF to form soot precursors (e.g. 1,3-cyclopentadiene or benzene) compared to less substituted furans and to other fuels has been experimentally observed and is well explained in the model.

This is Part II of a series of three papers which jointly address the combustion chemistry of furan and its alkylated derivatives 2-methylfuran (MF) and 2,5-dimethylfuran (DMF) under premixed low-pressure flame conditions. Some of them are considered to be promising biofuels. With furan as a common basis studied in Part I of this series, the present paper addresses two laminar premixed low-pressure (20 and 40 mbar) flat argon-diluted (50%) flames of MF which were studied with electron-ionization molecular-beam mass spectrometry (EI-MBMS) and gas chromatography (GC) for equivalence ratios φ=1.0 and 1.7, identical conditions to those for the previously reported furan flames. Mole fractions of reactants, products as well as stable and reactive intermediates were measured as a function of the distance above the burner. Kinetic modeling was performed using a comprehensive reaction mechanism for all three fuels given in Part I and described in the three parts of this series. A comparison of the experimental results and the simulation shows reasonable agreement, as also seen for the furan flames in Part I before. This set of experiments is thus considered to be a valuable additional basis for the validation of the model. The main reaction pathways of MF consumption have been derived from reaction flow analyses, and differences to furan combustion chemistry under the same conditions are discussed.

Complex reactive processes in the gas phase often proceed via numerous reaction steps and intermediate species that must be identified and quantified to develop an understanding of the reaction pathways and establish suitable reaction mechanisms. Here, photoelectron-photoion coincidence (PEPICO) spectroscopy has been applied to analyse combustion intermediates present in a premixed fuel-rich (ϕ = 1.7) ethene-oxygen flame diluted with 25% argon, burning at a reduced pressure of 40 mbar. For the first time, multiplexing fixed-photon-energy PEPICO measurements were demonstrated in a chemically complex reactive system such as a flame in comparison with the scanning "threshold" TPEPICO approach used in recent pioneering combustion investigations. The technique presented here is capable of detecting and identifying multiple species by their cations' vibronic fingerprints, including radicals and pairs or triplets of isomers, from a single time-efficient measurement at a selected fixed photon energy. Vibrational structures for these species have been obtained in very good agreement with scanning-mode threshold photoelectron spectra taken under the same conditions. From such spectra, the temperature in the ionisation volume was determined. Exemplary analysis of species profiles and mole fraction ratios for isomers shows favourable agreement with results obtained by more common electron ionisation and photoionisation mass spectrometry experiments. It is expected that the multiplexing fixed-photon-energy PEPICO technique can contribute effectively to the analysis of chemical reactivity and kinetics in and beyond combustion.

No abstract

Electron ionization, photoionization and photoelectron/photoion coincidence spectroscopy in mass-spectrometric investigations of a low-pressure ethylene/oxygen flame, Proc. Combust. Inst. 35 (2015) 779-786.

No abstract

Biodiesel combustion models demand detailed understanding of the reactions undertaken by the ester functional group in the molecule. Investigations of the chemistry of small methyl esters can contribute to this goal. We have thus chosen methyl propanonate (MP) as a representative ester molecule in a study combining theory, model, and experiments. As an advantage, its reactions are also amenable to high-level theoretical calculations. Based on recent theoretical calculations , a new kinetics model for small ester combustion was developed and validated. New experimental results were obtained here in an extensive range of conditions, including full speciation in laminar low-pressure flames at two different stoichiometries ( φ = 0.8 and 1.5) using electron ionization (EI) molecular-beam mass spectrometry (MBMS) and flame speed measurements in a spherical confined chamber (1-6 atm). Comparison of the experimental data to the present model shows overall improved performance. Some specific new reaction pathways to form methanol, methylketene, methyl acetate, and acetic acid from the fuel radicals were identified and will permit more detailed insights into the combustion properties of methyl propanoate.