The potential for the metal nanocatalyst to contaminate vapour-liquid-solid grown semiconductor nanowires has been a long-standing concern, because the most common catalyst material, Au, is highly detrimental to the performance of minority carrier electronic devices. We have detected single Au atoms in Si nanowires grown using Au nanocatalyst particles in a vapour-liquid-solid process. Using high-angle annular dark-field scanning transmission electron microscopy, Au atoms were observed in higher numbers than expected from a simple extrapolation of the bulk solubility to the low growth temperature. Direct measurements of the minority carrier diffusion length versus nanowire diameter, however, demonstrate that surface recombination controls minority carrier transport in as-grown n-type nanowires; the influence of Au is negligible. These results advance the quantitative correlation of atomic-scale structure with the properties of nanomaterials and can provide essential guidance to the development of nanowire-based device technologies.

We report a rapid, quantitative procedure for the evaluation of the carbonaceous purity of bulk quantities of as-prepared single-walled carbon nanotube (SWNT) soot by the utilization of solution-phase near-IR spectroscopy. The procedure starts with two steps of homogenization followed by solution/dispersion spectroscopy of a representative part of the bulk sample. The purity is evaluated against a reference sample by utilizing the region of the second interband transition (S 22 ) for semiconducting SWNTs. The procedure is found to be capable of reliably analyzing the carbonaceous purity of a 10-g batch of SWNTs produced by the electric arc discharge method to within 3%.

No abstract

Semiconductor nanowires show promise for many device applications, but controlled doping with electronic and magnetic impurities remains an important challenge. Limitations on dopant incorporation have been identified in nanocrystals, raising concerns about the prospects for doping nanostructures. Progress has been hindered by the lack of a method to quantify the dopant distribution in single nanostructures. Recently, we showed that atom probe tomography can be used to determine the composition of isolated nanowires. Here, we report the first direct measurements of dopant concentrations in arbitrary regions of individual nanowires. We find that differences in precursor decomposition rates between the liquid catalyst and solid nanowire surface give rise to a heavily doped shell surrounding an underdoped core. We also present a thermodynamic model that relates liquid and solid compositions to dopant fluxes.

We compare popular analytical techniques, including scanning and transmission electron microscopy (SEM and TEM), thermogravimetric analysis (TGA), and Raman and near-infrared (NIR) spectroscopy, for the evaluation of the purity of bulk quantities of single-walled carbon nanotubes (SWNTs). Despite their importance as imaging techniques, SEM and TEM are not capable of quantitatively evaluating the purity of typical inhomogeneous bulk SWNT samples because the image frame visualizes less than 1 pg of SWNT material; furthermore, there is no published algorithm to convert such images into numerical data. The TGA technique is capable of measuring the amount of metal catalyst in an SWNT sample, but does not provide an unambiguous separation between the content of SWNTs and carbonaceous impurities. We discuss the utilization of solution-phase near-infrared spectroscopy and solution-phase Raman spectroscopy to quantitatively compare arbitrary samples of bulk SWNT materials of different purities. The primary goal of this paper is to provide the chemical community with a realistic evaluation of current analytical tools for the purity evaluation of a bulk sample of SWNTs. The secondary goal is to draw attention to the growing crisis in the SWNT industry as a result of the lack of quality control and the misleading advertising by suppliers of this material.

Single-walled carbon nanotube (SWNT) reinforced polymer composite membranes have been fabricated using the electrospinning technique. Nanofibers with a diameter in the range 50−100 nm were obtained by electrospinning SWNT-filled polystyrene composites. TEM observations revealed incorporation of small SWNT bundles oriented parallel to the nanofiber axis. As-prepared (AP) and ester (EST) functionalized SWNTs have been electrospun with polyurethane (PU) to demonstrate the effect of the chemical functionalization of SWNTs on the mechanical properties of SWNT-reinforced composites. The tensile strength of EST-SWNT-PU membranes is enhanced by 104% as compared to electrospun pure polyurethane membranes, while an increase of only 46% was achieved incorporating AP−SWNT in the polyurethane matrix. The tangent moduli of AP-and EST-SWNT-PU membranes were found to be respectively 215% and 250% higher than the control polyurethane membranes.

Poly(aminobenzene sulfonic acid) (PABS) and polyethylene glycol (PEG) were covalently attached to single-walled carbon nanotubes (SWNTs) to form water-soluble graft copolymers. Quantitative near-IR (NIR) spectroscopic studies of these SWNT graft copolymers indicate a water solubility of about 5 mg/mL, and atomic force microscopy studies show a fairly uniform length and diameter. On the basis of thermogravimetric analysis, the loading of SWNTs in the graft copolymers is estimated to be 30% for SWNT-PABS and 71% for SWNT-PEG. NIR spectroscopic studies of SWNT-PABS show that this graft copolymer has a ground state that is a hybrid of the electronic structures of the isolated PABS and SWNT macromolecules.

Over the past few years, in situ transmission electron microscopy (TEM) studies of lithium ion batteries using an open-cell configuration have helped us to gain fundamental insights into the structural and chemical evolution of the electrode materials in real time. In the standard open-cell configuration, the electrolyte is either solid lithium oxide or an ionic liquid, which is point-contacted with the electrode. This cell design is inherently different from a real battery, where liquid electrolyte forms conformal contact with electrode materials. The knowledge learnt from open cells can deviate significantly from the real battery, calling for operando TEM technique with conformal liquid electrolyte contact. In this paper, we developed an operando TEM electrochemical liquid cell to meet this need, providing the configuration of a real battery and in a relevant liquid electrolyte. To demonstrate this novel technique, we studied the lithiation/delithiation behavior of single Si nanowires. Some of lithiation/delithation behaviors of Si obtained using the liquid cell are consistent with the results from the open-cell studies. However, we also discovered new insights different from the open cell configuration-the dynamics of the electrolyte and, potentially, a future quantitative characterization of the solid electrolyte interphase layer formation and structural and chemical evolution.