As the most commonly used hole transport material (HTM) in tin–lead (Sn–Pb) perovskite solar cells (PSCs), poly­(3,4-ethylenedioxythiophene) polystyrenesulfonate (PEDOT:PSS) limits the power conversion efficiency (PCE) and stability of the PSCs due to its acidic characteristics. Herein, an easily synthesized polymer HTM poly­[(phenyl)­imino­[9-(2-ethylhexyl)­carbazole]-2,7-diyl] (CzAn) with a shallow highest occupied molecular orbital (HOMO) level of −4.95 eV is used in a p-i-n structure, methylammonium-free, Sn–Pb PSC to replace PEDOT:PSS. Upon optimization using doping and surface engineering, high quality Sn–Pb PSCs could be successfully fabricated, boosting the PCE to 22.6% (stabilized PCE of 21.3%) compared with 21.2% for PEDOT:PSS. The perovskite films prepared on the modified CzAn HTM possess improved crystallinity, reduced trap-state density, and larger carrier mobility resulting in PSCs with greatly improved stability.

The development of low-cost materials for charge-selective contacts that provide good energetic alignment with perovskite active layers, favorable thermal properties, and lead to efficient photoconversion is becoming an increasingly important aspect of the perovskite solar cell (PSC) field. Presented here is a series of polymers based on a one-pot polymerization of aryl dihalides with primary aryl amines to produce solution-processable polymers in high yield, with simple purification, and promising properties for high performing P-I-N PSC devices. How these properties can be tuned by careful selection of the reactant chemical moieties is discussed. Through this strategy, a wide range of relevant properties such as glass transition temperature, highest occupied molecular orbital tuning, and polydispersity are explored. When implemented into devices using a triple-cation FAMACs perovskite active layer, the hole transport material series shows average power conversion efficiencies (PCE) in excess of 17%, which is comparable to controls using state-of-the-art poly(triarylamine). How different synthetic parameters such as the reaction time and purification protocol impact device performance is also investigated.

Metal halide perovskites are promising for optoelectronic device applications; however, their poor stability under solar illumination remains a primary concern. While the intrinsic photostability of isolated neat perovskite samples has been widely discussed, it is important to explore how charge transport layersemployed in most devicesimpact photostability. Herein, we study the effect of organic hole transport layers (HTLs) on light-induced halide segregation and photoluminescence (PL) quenching at perovskite/organic HTL interfaces. By employing a series of organic HTLs, we demonstrate that the HTL’s highest occupied molecular orbital energy dictates behavior; furthermore, we reveal the key role of halogen loss from the perovskite and subsequent permeation into organic HTLs, where it acts as a PL quencher at the interface and introduces additional mass transport pathways to facilitate halide phase separation. In doing so, we both reveal the microscopic mechanism of non-radiative recombination at perovskite/organic HTL interfaces and detail the chemical rationale for closely matching the perovskite/organic HTL energetics to maximize solar cell efficiency and stability.

While the performance of metal halide perovskite light-emitting diodes (PeLEDs) has rapidly improved in recent years, their stability remains a bottleneck to commercial realization. Here, we show that the thermal stability of polymer hole-transport layers (HTLs) used in PeLEDs represents an important factor influencing the external quantum efficiency (EQE) roll-off and device lifetime. We demonstrate a reduced EQE roll-off, a higher breakdown current density of approximately 6 A cm–2, a maximum radiance of 760 W sr–1 m–2, and a longer device lifetime for PeLEDs using polymer HTLs with high glass-transition temperatures. Furthermore, for devices driven by nanosecond electrical pulses, a record high radiance of 1.23 MW sr–1 m–2 and an EQE of approximately 1.92% at 14.6 kA cm–2 are achieved. Thermally stable polymer HTLs enable stable operation of PeLEDs that can sustain more than 11.7 million electrical pulses at 1 kA cm–2 before device failure.

As lead halide perovskites (LHPs) continue to achieve success as a lightharvesting material in perovskite solar cells (PSCs), exploring and understanding other materials in the device stack become increasingly important. Particularly, selection of suitable hole transport materials (HTMs) that demonstrate high performance and stability is imperative in the design of P−I−N PSCs. Presented here are a family of 12 structurally related polymers based on either fluorene or carbazole main chains with select aromatic side groups that introduce tunable properties for use in PSCs. How properties such as the highest occupied molecular orbital energy level, conductivity, glass-transition temperature, and wettability of the HTM affect the PSC performance is explored. Devices that incorporate the polymer HTMs perform well relative to PTAA in benchmark P−I−N PSC architectures while exhibiting similar or superior stability under accelerated aging studies. The relative synthetic simplicity and resultant performance of the HTMs in PSCs coupled with the ability to customize properties with different functional groups demonstrates the potential of this family of HTMs for a variety of LHP materials.