No abstract

Stresses were generated after screw tightening of the frameworks, increasing when a load was applied and when a vertical gap was present. Angled implants resulted in oblique stress patterns, which were not transferred with homogeneity to the polymeric model.

bone-resorption may occur. The loading threshold tolerated by the bone is not well-known and the failure of osseointegration can be caused by bone resorption as a result of unfavorable stress concentrations 11 . In accordance to Kohn 16 (1992), tension distribution is one of the important factors related to implant success; the tensions should be transferred to the adjacent bone, preferentially in an orientation and magnitude that keep the tissues viability near a physiologic state. * Graduate Students; **Assistant Professors -Department of Prosthodontics, School of Dentistry, University of São Paulo. ABSTRACT:The longevity of implant-supported prosthetic rehabilitation depends largely on how the masticatory forces are transferred to the implants and surrounding bone. Anatomical conditions, bone morphology and aesthetics usually dictate implant placement in less than ideal positions for prosthetic rehabilitation and sometimes it is possible to find them with different inclinations. The purpose of this paper was to compare, through photoelastic analysis, the stress distribution in a fixed prosthesis with 3 parallel implants, to the stress distribution in the same prosthesis in the existence of an angled central implant. Two photoelastic resin models were made and a polariscope was used in the visualization of isochromatic fringes formed in the models when axial loads of 2 kg, 5 kg and 10 kg were applied to a unique central point of the prosthesis. The presence of inducted tensions (preloads) was observed in the models after applying torque to the retention screws. Preloads were intensified with the incidence of occlusal forces. In the parallel implants, the force dissipation followed the long axis. The angled implant had a smaller quantity of fringes and the stresses were located mostly around the apical region of the lateral implants. DESCRIPTORS: Dental implantation, endosseous; Prosthesis implantation. RESUMO:A longevidade das reabilitações orais implanto-suportadas depende, em grande parte, de como as forças mastigatórias são transferidas aos implantes e ao osso que os circunda. Condições anatômicas, morfologia óssea e estética muitas vezes ditam a colocação de implantes em posições que não são ideais para a reabilitação protética, e podemos encontrá-los com diferentes inclinações. A proposta deste trabalho foi comparar, através de análise fotoelástica, a dissipação de tensões em uma prótese fixa com 3 implantes paralelos entre si com a dissipação de tensões na mesma prótese na existência do implante central angulado. Foram confeccionados dois modelos de resina fotoelástica. Utilizou-se um polariscópio para visualização das franjas isocromáticas que se formaram nos modelos fotoelásticos quando cargas axiais de 2 kg, 5 kg e 10 kg foram aplicadas em um mesmo ponto central da prótese. Verificou-se a indução de tensões (pré-tensões) nos modelos após o apertamento dos parafusos de retenção das próteses. As pré-tensões foram agravadas com a incidência de forças oclusais. Nos implantes paralelos, a dissipação de for...

This study evaluated, in vivo, the efficacy of a denture glazing material (Palaseal) in modifying plaque colonization of dentures. Ten subjects were selected and received maxillary temporary partial removable dentures, with complete acrylic palatal coverage. The right half of the fitting surface of the denture bases were glazed with Palaseal, whereas the other half was not glazed. One month after insertion, two fragments of the resin base of all dentures were removed (one from the glazed side and another from the non-glazed side). These samples were prepared and examined by scanning electron microscopy. Three months after insertion, other fragments were obtained and analyzed. Microscopic observation at 1 month revealed that, for all patients, the plaque film was thinner on the treated side in comparison to the non-treated side. However, at the 3-month evaluation, some areas of the glaze showed cracking, and both glazed and non-glazed sides were covered by a dense bacterial plaque film. In conclusion, the findings of this clinical experiment showed that glazing denture's fitting surface did not prevent bacterial colonization, but favored plaque removal while the glaze layer remained intact. After three months, glaze cracks created microretentive areas that increased plaque accumulation.

No abstract

The digital smile design is a practical diagnosis method that can assist the clinician to visualize and measure dentogingival discrepancies. This clinical report aims to present the associated steps, from the diagnosis of the alterations diagnosis through to the final aesthetic result. A 37-years-old female patient presented as her main complaint the tooth form and colour discrepancies. Applying the digital smile design principle, the necessary measures for a harmonic smile correction could be accurately determined. The initial diagnosis led to a wax up of the master cast that was duplicated in acrylic resin directly in the mouth. This temporary restoration guided the periodontal surgery and the final pressed ceramic crown restoration. We conclude that the digital smile design concept seems to be a useful tool to achieve a satisfactory aesthetic result.

No abstract

No abstract