Carbon nanotubes have many material properties that make them attractive for applications. In the context of nanoelectronics, interest has focused on single-walled carbon nanotubes (SWNTs) because slight changes in tube diameter and wrapping angle, defined by the chirality indices (n, m), will shift their electrical conductivity from one characteristic of a metallic state to one characteristic of a semiconducting state, and will also change the bandgap. However, this structure-function relationship can be fully exploited only with structurally pure SWNTs. Solution-based separation methods yield tubes within a narrow structure range, but the ultimate goal of producing just one type of SWNT by controlling its structure during growth has proved to be a considerable challenge over the last two decades. Such efforts aim to optimize the composition or shape of the catalyst particles that are used in the chemical vapour deposition synthesis process to decompose the carbon feedstock and influence SWNT nucleation and growth. This approach resulted in the highest reported proportion, 55 per cent, of single-chirality SWNTs in an as-grown sample. Here we show that SWNTs of a single chirality, (12, 6), can be produced directly with an abundance higher than 92 per cent when using tungsten-based bimetallic alloy nanocrystals as catalysts. These, unlike other catalysts used so far, have such high melting points that they maintain their crystalline structure during the chemical vapour deposition process. This feature seems crucial because experiment and simulation both suggest that the highly selective growth of (12, 6) SWNTs is the result of a good structural match between the carbon atom arrangement around the nanotube circumference and the arrangement of the catalytically active atoms in one of the planes of the nanocrystal catalyst. We anticipate that using high-melting-point alloy nanocrystals with optimized structures as catalysts paves the way for total chirality control in SWNT growth and will thus promote the development of SWNT applications.

Black phosphorus (BP) has attracted significant interest as a monolayer or few-layer material with extraordinary electrical and optoelectronic properties. However, degradation in air and other environments is an unresolved issue that may limit future applications. In particular the role of different ambient species has remained controversial. Here, we report systematic experiments combined with ab-initio calculations that address the effects of oxygen and water in the degradation of BP. Our results show that BP rapidly degrades whenever oxygen is present, but is unaffected by deaerated (i.e., O 2 depleted) water. This behavior is rationalized by oxidation involving a facile dissociative chemisorption of O 2 , whereas H 2 O molecules are weakly physisorbed and do not dissociate on the BP surface. Oxidation (by O 2 ) turns the hydrophobic pristine BP surface progressively hydrophilic. Our results have implications on the development of encapsulation strategies for BP, and open new avenues for exploration of phenomena in aqueous solutions including solution-gating, electrochemistry, and solutionphase approaches for exfoliation, dispersion, and delivery of BP.

No abstract

Fast-growth of single crystal monolayer graphene by CVD using methane and hydrogen has been achieved on "homemade" single crystal Cu/Ni(111) alloy foils over large area. Full coverage was achieved in 5 min or less for a particular range of composition (1.3 at.% to 8.6 at.% Ni), as compared to 60 min for a pure Cu(111) foil under identical growth conditions. These are the bulk atomic percentages of Ni, as a superstructure at the surface of these foils with stoichiometry CuNi (for 1.3 to 7.8 bulk at.% Ni in the Cu/Ni(111) foil) was discovered by low energy electron diffraction (LEED). Complete large area monolayer graphene films are either single crystal or close to single crystal, and include folded regions that are essentially parallel and that were likely wrinkles that "fell over" to bind to the surface; these folds are separated by large, wrinkle-free regions. The folds occur due to the buildup of interfacial compressive stress (and its release) during cooling of the foils from 1075 °C to room temperature. The fold heights measured by atomic force microscopy (AFM) and scanning tunneling microscopy (STM) prove them to all be 3 layers thick, and scanning electron microscopy (SEM) imaging shows them to be around 10 to 300 nm wide and separated by roughly 20 μm. These folds are always essentially perpendicular to the steps in this Cu/Ni(111) substrate. Joining of well-aligned graphene islands (in growths that were terminated prior to full film coverage) was investigated with high magnification SEM and aberration-corrected high-resolution transmission electron microscopy (TEM) as well as AFM, STM, and optical microscopy. These methods show that many of the "join regions" have folds, and these arise from interfacial adhesion mechanics (they are due to the buildup of compressive stress during cool-down, but these folds are different than for the continuous graphene films-they occur due to "weak links" in terms of the interface mechanics). Such Cu/Ni(111) alloy foils are promising substrates for the large-scale synthesis of single-crystal graphene film.

Single-crystal metals have distinctive properties owing to the absence of grain boundaries and strong anisotropy. Commercial single-crystal metals are usually synthesized by bulk crystal growth or by deposition of thin films onto substrates, and they are expensive and small. We prepared extremely large single-crystal metal foils by “contact-free annealing” from commercial polycrystalline foils. The colossal grain growth (up to 32 square centimeters) is achieved by minimizing contact stresses, resulting in a preferred in-plane and out-of-plane crystal orientation, and is driven by surface energy minimization during the rotation of the crystal lattice followed by “consumption” of neighboring grains. Industrial-scale production of single-crystal metal foils is possible as a result of this discovery.

Anodes involving conversion and alloying reaction mechanisms are attractive for potassium‐ion batteries (PIBs) due to their high theoretical capacities. However, serious volume change and metal aggregation upon potassiation/depotassiation usually cause poor electrochemical performance. Herein, few‐layered SnS2 nanosheets supported on reduced graphene oxide (SnS2@rGO) are fabricated and investigated as anode material for PIBs, showing high specific capacity (448 mAh g−1 at 0.05 A g−1), high rate capability (247 mAh g−1 at 1 A g−1), and improved cycle performance (73% capacity retention after 300 cycles). In this composite electrode, SnS2 nanosheets undergo sequential conversion (SnS2 to Sn) and alloying (Sn to K4Sn23, KSn) reactions during potassiation/depotassiation, giving rise to a high specific capacity. Meanwhile, the hybrid ultrathin nanosheets enable fast K storage kinetics and excellent structure integrity because of fast electron/ionic transportation, surface capacitive‐dominated charge storage mechanism, and effective accommodation for volume variation. This work demonstrates that K storage performance of alloy and conversion‐based anodes can be remarkably promoted by subtle structure engineering.

The process of oxidation of a copper surface coated by a layer of graphene in water-saturated air at 50 °C was studied where it was observed that oxidation started at the graphene edge and was complete after 24 h. Isotope labeling of the oxygen gas and water showed that the oxygen in the formed copper oxides originated from water and not from the oxygen in air for both Cu and graphene-coated Cu, and this has interesting potential implications for graphene as a protective coating for Cu in dry air conditions. We propose a reaction pathway where surface hydroxyl groups formed at graphene edges and defects induce the oxidation of Cu. DFT simulation shows that the binding energy between graphene and the oxidized Cu substrate is smaller than that for the bare Cu substrate, which facilitates delamination of the graphene. Using this process, dry transfer is demonstrated using poly­(bisphenol A carbonate) (PC) as the support layer. The high quality of the transferred graphene is demonstrated from Raman maps, XPS, STM, TEM, and sheet resistance measurements. The copper foil substrate was reused without substantial weight loss to grow graphene (up to 3 cycles) of equal quality to the first growth after each cycle. It was found that dry transfer yielded graphene with less Cu impurities as compared to methods using etching of the Cu substrate. Using PC yielded graphene with less polymeric residue after transfer than the use of poly­(methyl methacrylate) (PMMA) as the supporting layer. Hence, this dry and clean delamination technique for CVD graphene grown on copper substrates is highly advantageous for the cost-effective large-scale production of graphene, where the Cu substrate can be reused after each growth.

The development of sodium-ion batteries is hindered by the poor Na + transport kinetics and structural instability of electrode materials during Na + intercalation/deintercalation. In this work, surface-dominated Na storage is demonstrated on the oxygen-functionalized graphene nanosheets (FGS) with fast surface redox reaction and robust structural stability. The FGS samples with tunable oxygen contents and species are fabricated via a two-step thermal exfoliation method from graphite oxides. The surface-induced oxygen functional groups can serve as the surface-redox sites for the FGS electrode, attaining a high specific capacity of 603 mAh g −1 at a current density of 0.05 A g −1 , excellent rate capability (214 mAh g −1 at 10 A g −1 ), and ultrastable cycling stability (capacity retention close to 100% after 10 000 cycles at 5 A g −1 ). Even at a slow scan rate of 0.1 mV s −1 for cyclic voltammetry, about 67.7% capacity is contributed from the surface adsorption/desorption and surface-redox reaction, suggesting surface-dominated Na storage for the FGS-700 (FGS sample obtained at 700 °C) electrode. The present work demonstrates that the surface oxygen functionalization is an effective strategy to develop high-performance graphene-based anodes due to the surface-dominated Na storage with improved reaction kinetics and suppressed structural variation.