The article shows studies of the problem of active sediment formation during mixing of residual fuels, caused by the manifestation of incompatibility. To preserve the quality and reduce sediment formation during transshipment, storage, and transportation of marine residual fuels, a laboratory method for determining the compatibility and stability of fuels has been developed, which makes it possible to determine the quantitative characteristics of the sediment formation activity. According to the method developed, laboratory studies have been carried out to determine incompatible fuel components and the influence of composition on the sedimentation process. Tests were carried out to determine the quality indicators and the individual group composition of the fuel samples. Based on the results of the studies, the dependences of the influence of normal structure paraffins in the range from 55 to 70 wt. % and asphaltenes in the range from 0.5 to 3.5 wt. % in the fuel composition on the sedimentation activity due to incompatibility were obtained. To obtain a convenient tool that is applicable in practice, a nomogram has been developed on the basis of the dependences obtained experimentally. It was also determined that, after reaching the maximum values of sediment formation with a further increase in the content of n-paraffins, saturation is observed, and the value of the sediment content remains at the same level. Maximum total sediment values have been found to depend on asphaltene content and do not significantly exceed them within 10%. The results of the research presented in this article allow laboratory and calculation to determine the possibility of incompatibility and to preserve the quality of marine residual fuels.
Well killing is an important technological stage before conducting workover operation, one of the tasks of which is to preserve and restore the natural filtration characteristics of the bottomhole formation zone (BFZ). Special attention should be paid to the choice of well killing technologies and development of wells in complicated conditions, which include abnormally low reservoir pressure, high oil-gas ratio and carbonate reservoir type. To preserve the filtration characteristics of the productive formation and prevent fluid losses in producing wells during well killing operation, blocking compositions are used. At the same time, an informed choice of the most effective well killing technologies is required. Consequently, there is a need to conduct laboratory physicochemical and coreflood experiments simulating geological, physical, and technological conditions of field development, as similar as possible to actual reservoir conditions. The article presents the results of experimental studies on the development well killing technologies of producing wells during workover operation in various geological, physical, and technological conditions of oil field development. Physicochemical and coreflood laboratory experiments were carried out with the simulation of the processes of well killing and development of wells in reservoir conditions with the use of modern high-technology equipment in the Enhanced Oil Recovery Laboratory of the Department of Development and Operation of Oil and Gas Fields at St. Petersburg Mining University. As a result of the experimental studies, new compositions of well killing and stimulation fluids were developed, which ensure to prevent fluid loss, gas breakthrough, as well as the preservation, restoration and improvement of the filtration characteristics of the BFZ in the conditions of terrigenous and carbonate reservoirs at different stages of oil field development. It is determined that the developed process fluids, which include surfactants (YALAN-E2 and NG-1), have a hydrophobic effect on the porous medium of reservoir rocks, which ultimately contributes to the preservation, restoration and improvement of the filtration characteristics of the BFZ. The value of the presented research results is relevant for practice and confirmed by the fact that, as a result of field tests of the technology for blocking the BFZ with the composition of inverse water–oil emulsion during well killing before workover operation, an improvement in the efficiency of wells operation was obtained in the form of an increase in their oil production rate by an average of 5–10 m3/day, reducing the time required for the well to start operating up to 1–3 days and reducing the water cut of formation fluid by 20–30%.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.