No abstract

The development of dense networks of broad-band seismographs makes teleseismic data amenable to full-waveform inversion (FWI) methods for high-resolution lithospheric imaging. Compared to scattered-field migration, FWI seeks to involve the full seismic wavefield in the inversion. We present a parametric analysis of 2-D frequency-domain FWI in the framework of lithospheric imaging from teleseismic data to identify the main factors that impact on the quality of the reconstructed compressional (P)-wave and shear (S)-wave speed models. Compared to controlled-source seismology, the main adaptation of FWI to teleseismic configuration consists of the implementation with a scattered-filed formulation of plane-wave sources that impinge on the base of the lithospheric target located below the receiver network at an arbitrary incidence angle. Seismic modelling is performed with a hp-adaptive discontinuous Galerkin method on unstructured triangular mesh. A quasi-Newton inversion algorithm provides an approximate accounting for the Hessian operator, which contributes to reduce the footprint of the coarse acquisition geometry in the imaging. A versatile algorithm to compute the gradient of the misfit function with the adjoint-state method allows for abstraction between the forward-problem operators and the meshes that are during seismic modelling and inversion, respectively. An approximate correction for obliquity is derived for future application to real teleseismic data under the two-dimension approximation. Comparisons between the characteristic scales involved in exploration geophysics and in teleseismic seismology suggest that the resolution gain provided by full waveform technologies should be of the same order of magnitude for both applications. We first show the importance of the surface-reflected wavefield to dramatically improve the resolving power of FWI by combining tomography-like and migration-like imaging through the incorporation of the forward-scattered and the backscattered wavefields in the inversion. The resolution of FWI is assessed through checkerboard tests and confirms a resolution of the order of the wavelength for both the P and S speeds, when the full wavefield is incorporated in the inversion. Secondly, we show that computationally efficient strategies, which consist of decimating the number of frequency components involved in the inversion, do not apply to teleseismic acquisitions, because the scattering-angle bandwidth sampled by plane-wave sources can be narrow and coarsely sampled, compared to that provided by dense profiles of point sources in exploration seismology. The waveform inversion is less sensitive to the band of incidence angles spanned by the plane-wave sources and to the sampling of this band. However, the deficit of vertically propagating plane waves hampers the vertical resolution of planar layers. Aliasing artefacts created by coarse arrays of receivers are illustrated. We show how taking into account the Hessian in the inversion and the suitable management of frequencies in the ...

HAL is a multi-disciplinary open access archive for the deposit and dissemination of scientific research documents, whether they are published or not. The documents may come from teaching and research institutions in France or abroad, or from public or private research centers. L'archive ouverte pluridisciplinaire HAL, est destinée au dépôt et à la diffusion de documents scientifiques de niveau recherche, publiés ou non, émanant des établissements d'enseignement et de recherche français ou étrangers, des laboratoires publics ou privés.

No abstract

We present an application of 2D acoustic frequency-domain Full Waveform Inversion (FWI) to the hydrophone component of 4-C ocean bottom cable (OBC) data recorded from the Valhall field in North sea. The starting model for FWI was built by reflection traveltime tomography (RTT). Although this starting model leads to flat common-image gathers (CIGs), it does not allow us to match first-arrival traveltimes of diving waves from above the gas layers. This mismatch between vertical and horizontal velocities is likely the footprint of anisotropy. We updated the RTT model by first-arrival traveltime tomography (FATT) to build a new starting model for FWI. The velocities above the gas layers of the updated model are significantly higher than velocities from in-well seismic (VSP) data. FWI models were computed from the two starting models just mentioned. More stable results were obtained with the starting model updated by FATT. The resulting FWI model shows a reasonable agreement with a former model developed by 3D FWI. A reasonable match of both short-aperture and wideaperture components of the data was obtained by isotropic FWI. This might indicate that layer-induced anisotropy was created by FWI in the gas layers to balance the increase of the shallow velocities created by the inversion of the wide-aperture data components.

No abstract

Full waveform inversion (FWI) of seismic traces recorded at the free surface allows the reconstruction of the physical parameters structure on the underlying medium. For such a reconstruction, an optimization problem is defined, where synthetic traces, obtained through numerical techniques as finite-difference or finite-element methods in a given model of the subsurface, should match the observed traces. The number of data samples is routinely around 1 billion for 2D problems and 1 trillion for 3D problems while the number of parameters ranges from 1 million to 10 million degrees of freedom. Moreover, if one defines the mismatch as the standard least-squares norm between values sampled in time/frequency and space, the misfit function has a significant number of secondary minima related to the ill-posedness and the nonlinearity of the inversion problem linked to the so-called cycle skipping. Taking into account the size of the problem, we consider a local linearized method where gradient is computed using the adjoint formulation of the seismic wave propagation problem. Starting for an initial model, we consider a quasi-Newtonian method, which allows us to formulate the reconstruction of various parameters such as P and S waves velocities or density or attenuation factors. A hierarchical strategy based on the incremental increase of the data complexity starting from low-frequency content to high-frequency content, from initial wavelets to later phases in the data space from narrow azimuths to wide azimuths and from simple observables to more complex ones. Different synthetic examples on realistic structures illustrate the efficiency of this strategy based on the data manipulation. This strategy related to the data space has to be inserted into a more global framework where we could improve significantly the probability to converge to the global minimum. When considering the model space, we may rely on the construction of the initial model or add constraints such as smoothness of the searched model and/or prior informations collected by other means. An alternative strategy concerns the building of the objective function and various possibilities must be considered, which may increase the linearity of the inversion procedure.

No abstract