A micromechanical torsion oscillator has been used to strengthen the limits on new Yukawa forces by determining the Casimir pressure between two gold-coated plates. By significantly reducing the random errors and obtaining the electronic parameters of the gold coatings, we were able to conclusively exclude the predictions of large thermal effects below 1 µm and strengthen the constraints on Yukawa corrections to Newtonian gravity in the interaction range from 29.5 nm to 86 nm.

We present supplementary information on the recent indirect measurement of the Casimir pressure between two parallel plates using a micromachined oscillator. The equivalent pressure between the plates is obtained by means of the proximity force approximation after measuring the force gradient between a gold coated sphere and a gold coated plate. The data are compared with a new theoretical approach to the thermal Casimir force based on the use of the Lifshitz formula, combined with a generalized plasmalike dielectric permittivity which takes into account interband transitions of core electrons. The theoretical Casimir pressures calculated using the new approach are compared with those computed in the framework of the previously used impedance approach and also with the Drude model approach. The latter is shown to be excluded by the data at a 99.9% confidence level within a wide separation range from 210 to 620 nm. The level of agreement between the data and theoretical approaches based on the generalized plasma model, or the Leontovich surface impedance, is used to set stronger constraints on the Yukawa forces predicted from the exchange of light elementary particles and/or extra-dimensional physics. The resulting constraints are the strongest in the interaction region from 20 to 86 nm with a largest improvement by a factor of 4.4 at 26 nm.

We apply the proximity force approximation, which is widely used for the calculation of the Casimir force between bodies with nonplanar boundary surfaces, to gravitational and Yukawa-type interactions. It is shown that for the gravitational force in a sphere-plate configuration the general formulation of the proximity force approximation is well applicable. For a Yukawa-type interaction we demonstrate the validity of both the general formulation of the proximity force approximation, and a simple mapping between the sphere-plate and plate-plate configurations. The claims to the contrary in some recent literature are thus incorrect. Our results justify the constraints on the parameters of non-Newtonian gravity previously obtained from the indirect dynamic measurements of the Casimir pressure.

We report new constraints on extra-dimensional models and other physics beyond the standard model based on measurements of the Casimir force between two dissimilar metals for separations in the range 0.2-1.2 m. The Casimir force between a Au-coated sphere and a Cu-coated plate of a microelectromechanical torsional oscillator was measured statically with an absolute error of 0.3 pN. In addition, the Casimir pressure between two parallel plates was determined dynamically with an absolute error of Ϸ0.6 mPa. Within the limits of experimental and theoretical errors, the results are in agreement with a theory that takes into account the finite conductivity and roughness of the two metals. The level of agreement between experiment and theory was then used to set limits on the predictions of extra-dimensional physics and thermal quantum field theory. It is shown that two theoretical approaches to the thermal Casimir force which predict effects linear in temperature are ruled out by these experiments. Finally, constraints on Yukawa corrections to Newton's law of gravity are strengthened by more than an order of magnitude in the range 56 -330 nm.

mechanical oscillators are present in almost every electronic device. They mainly consist of a resonating element providing an oscillating output with a specific frequency. Their ability to maintain a determined frequency in a specified period of time is the most important parameter limiting their implementation. Historically, quartz crystals have almost exclusively been used as the resonating element, but micromechanical resonators are increasingly being considered to replace them. These resonators are easier to miniaturize and allow for monolithic integration with electronics. However, as their dimensions shrink to the microscale, most mechanical resonators exhibit nonlinearities that considerably degrade the frequency stability of the oscillator. Here we demonstrate that, by coupling two different vibrational modes through an internal resonance, it is possible to stabilize the oscillation frequency of nonlinear self-sustaining micromechanical resonators. our findings provide a new strategy for engineering low-frequency noise oscillators capitalizing on the intrinsic nonlinear phenomena of micromechanical resonators.