ЛАБОРАТОРНЫЕ ИССЛЕДОВАНИЯ ТРЕНИЯ СТАЛИ ШХ15 ПО ПОКРЫТИЮ НА ОСНОВЕ SIO 2 , СОДЕРЖАЩЕМУ НАНОЧАСТИЦЫ MOS 2 СО СРЕДНИМ РАЗМЕРОМ 64 НМ В настоящее время представляет практический интерес выявление закономерностей влияния наночастиц дисульфида молибдена на трение в парах трения «сталь − беспористое нанокомпозиционное покрытие» для увеличения антифрикционных свойств покрытий триботехнического назначения. В границах данной работы приведены результаты исследований трения верчения стали марки ШХ15 по поверхности беспористого покрытия с матрицей из диоксида кремния, наполненного наночастицами дисульфида молибдена размером 64 нм в концентрации 73%, нанесённого на подложку из нержавеющей стали марки 12Х18Н10Т. Для исследования были взяты образцы из стали 12Х18Н10Т, с нанесенными на них покрытиями из SiO2 и SiO2+73%MoS2 (64нм). Толщина нанесенных беспористых покрытий составляла около 1мкм. В качестве вращающегося контртела использовался цилиндрический образец (ролик) из подшипниковой стали марки ШХ-15, диаметром 10мм. Выбранный твёрдый смазочный материал-наноразмерный порошкообразный дисульфид молибдена шарообразной формы. В процессе испытаний вращающийся стальной образец своей плоской частью прижимался к плоскости зажатого в струбцине образца. Струбцина, зафиксированная на подшипниковом узле, с помощью тросика и тензобалки в процессе опыта удерживалась от поворота, сообщаемого подвижным роликом. С тензобалки на компьютер передавались данные о силе трения и действующей нагрузке. В процессе всех опытов нагрузка на пару трения составляла 250 Н, а частота вращения вала, в котором был зажат стальной ролик, составляла 450 об/мин, время трения составляло 600 с. Экспериментально установлено, что в результате трения верчения по схеме «плоскостьплоскость» образца из подшипниковой стали ШХ15 по нанокомпозиционному покрытию наблюдаются антифрикционные эффекты относительно аналогичных испытаний покрытия из ненаполненного наночастицами диоксида кремния. Показано стабилизирующее действие наночастиц на процесс фрикционного взаимодействия в режиме трения верчения.
New developments for continuous pouring of steel are considered, including slide gates, refractories, promising technologies, etc. A comparative analysis of the designs of domestic and foreign manufacturers is given and the basic operating characteristics and criteria for the selection of refractory slabs for slide gates are presented. The latest developments from NPP Vulkan-TM related to the creation of equipment for continuous casting of steel are considered.The widespread application of the method of continuous-continuous casting and highly durable refractory materials has greatly increased the requirements imposed on the rate of turn-over of teeming ladles and for reduced service times and has entailed the use of modern slide casting systems to enable increases in the level of automation of the processes involving in casting of metal and reductions in the unit costs for these processes. To solve this problem it is necessary to select an efficient design of a slide valve system and arrive at an optimal choice of the consumable refractory set. From an analysis of the evolution of the development of slide valve systems it becomes possible to formulate the requirements that have to be imposed on the new generation of slide valve systems to achieve highly productive multiple-strand continuous seal casting:-multipoint spring-actuated mechanism for uniform compression of refractory slabs; -elevated lifetime of components and parts of the system; -the presence of a system for clamping of the refractory slabs;-minimization of the human factor in operation of the system; -rapidity and ease of replacement of refractory materials. The use of modern designs enables us to achieve a high degree of uniformity in the application of a clamping force to refractory slabs, ensure their automatic adjustment, compensate for cyclic thermal expansions and wear of the refractory Fig. 1. Models of slide gates from foreign manufacturers corresponding to modern requirements: a) cartridge-type gate with independent sliders from the firm of Vesuvius (Austria); b) cartridge-type equalizing-type gate from NPO Doniks (Ukraine).
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.