No abstract

No abstract

This article reports on the effects of a new combined wet milling technique on the physicochemical properties of meloxicam (MEL). The influence of milling time on the particle size, the crystallinity, the morphology and the dissolution rate of MEL has been studied in the presence and absence of polyvinyl alcohol (PVA) as a stabilizer agent. Micronized MEL particles were produced in aqueous medium which did not contain additive after milling for 10 min. For nanonization an additive and longer milling time were required. After particle size determination the structural and morphological characterization of the wet milled, dried products containing MEL were studied. X-ray powder diffractometry (XRPD) and differential scanning calorimetry (DSC) examinations revealed the change in the crystallinity of MEL. Scanning electron microscopy (SEM) images showed that aggregates of nanosized MEL particles were formed, regardless of the presence of PVA. The nanonized MEL crystals (D 50 = 126 nm) exhibited a regular shape and a smooth surface. The increased specific surface area resulted in a high dissolution rate and concentration of free MEL. According to the results, the produced samples could be applied as a basic material (micronized MEL) and intermediate product (micronized and nanonized MEL with PVA) for the design of dosage forms.

The aim of this article was to study the trans-epithelial absorption to reach the blood and to target the brain by axonal transport using nasal formulations with nanonized meloxicam (nano MEL spray) and its salt form known as meloxicam potassium monohydrate (MELP spray). The physicochemical properties and the mucoadhesivity of nasal formulations were controlled. In vitro and in vivo studies were carried out. These forms were first investigated in “nose-to-brain” relation. It was found that the in vitro study and in vivo study did not show any significant correlation. In vitro experiments demonstrated faster dissolution rate and higher diffusion of MELP from the spray compared with the nano MEL spray. The administration of the nano MEL spray resulted in faster absorption and constant plasma concentration of the drug after five minutes of administration as compared to MELP. The axonal transport of the drug was justified. MEL appeared in the brain tissues after the first five minutes of administration in the case of both spray forms, but its amount was too small in comparison with the total plasma concentration. The application of the nano MEL spray resulted in the same AUC in the brain as the intravenous injection. The “nose-to-blood” results predicted the nasal applicability of MEL and MELP in pain management. The “nose-to-brain” pathway requires further study.

Besides the opioids the standard management of the World Health Organization suggests NSAIDs (non-steroidal anti-inflammatory drugs) alone or in combination to enhance analgesia in malignant and non-malignant pain therapy. The applicability of NSAIDs in a nasal formulation is a new approach in pharmaceutical technology. In order to enhance the nasal absorption of meloxicam (MX) as an NSAID, its salt form, meloxicam potassium monohydrate (MXP), registered by Egis Plc., was investigated in comparison with MX. The physico-chemical properties of the drugs (structural analysis, solubility and dissolution rate) and the mucoadhesivity of nasal formulations were controlled. In vitro and in vivo studies were carried out to determine the nasal applicability of MXP as a drug candidate in pain therapy. It can be concluded that MX and MXP demonstrated the same equilibrium solubility at the pH5.60 of the nasal mucosa (0.017mg/ml); nonetheless, MXP indicated faster dissolution and a higher permeability through the synthetic membrane. The animal studies justified the short T value (15min) and the high AUC of MXP, which is important in acute pain therapy. It can be assumed that the low mucoadhesivity of MXP spray did not increase the residence time in the nasal cavity, and the elimination from the nasal mucosa was therefore faster than in the case of MX. Further experiments are necessary to prove the therapeutic relevance of this MXP-containing innovative intranasal formulation.

No abstract

This article reports on particle engineering by a top-down method involving the organic solvent-free acoustic cavitation. The effects on particle size reduction of static and dynamic sonication methods were compared. The process parameters (volume, position and amplitude of sonotrode, concentration of drug, temperature, sonication time rpm of pump) were optimized by factorial design plan for particle size distribution of meloxicam (MEL) as response factor after sonication. It was found, that in case of the static sonication small sample volume, high amplitude and long sonication time influenced principally on the particle size reduction. Interactions were observed between amplitude of sonication, position of sonotrode and volume. By the dynamic sonication low rpm of pump, high amplitude and long sonication time were the dominant parameters. There was a correlation between the increased amplitude and temperature. Grinding with optimized process parameters resulted in 10.16 μm average particle size with static, and 14.60 μm with dynamic sonication. Samples sonicated with appropriate process parameters, were dried and characterized. During the solid state analysis scanning electron microscopy (SEM) images showed, that the sonication resulted in a rounded habit of the particles. The thermoanalytical (DSC) and X-ray powder diffraction (XRPD) characterization displayed the crystalline structure of MEL in both cases. The FT-IR images demonstrated that no chemical degradation occured. The static sonication is recommended for development of preclinical samples, the dynamic sonication is suitable for scale-up of the static method.

Abstract:The nasal route receives a great deal of attention as a non-invasive method for the systemic administration of drugs. For nasal delivery, specific formulations containing excipients are used. Because of the sensitive respiratory mucosa, not only the active ingredients, but also additives need to be tested in appropriate models for toxicity. The aim of the study was to measure the cytotoxicity of six pharmaceutical excipients, which could help to reach larger residence time, better permeability, and increased solubility dissolution rate. The following excipients were investigated on RPMI 2650 human nasal septum tumor epithelial cells: β-D-mannitol, sodium hyaluronate, α and β-cyclodextrin, polyvinyl alcohol and methylcellulose. 3-(4,5-dimethyltiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) dye conversion assay and real-time impedance analysis were used to investigate cytotoxicity. No excipient showed toxicity at 0.3% (w/v) concentration or below while 1% concentration a significantly reduced metabolic activity was measured by MTT assay for methylcellulose and cyclodextrins. Using impedance measurements, only β-cyclodextrin (1%) was toxic to cells. Mannitol at 1% concentration had a barrier opening effect on epithelial cells, but caused no cellular damage. Based on the results, all additives at 0.3%, sodium hyaluronate and polyvinyl alcohol at 1% concentrations can be safely used for nasal formulations.