In juice processing, ultrasound treatment has been tested as a potential alternative to conventional thermal methods to inactivate microorganisms and to enhance the nutritional status of juice. In this study, the impact of pasteurization and high-power ultrasound treatment on the quality of red grape juice was investigated in terms of the content of bioactive compounds such as phenolic compounds and l-ascorbic acid as well as regarding the microbiological and physicochemical properties. The grape juice was subjected to pasteurization (80 °C, 2 min) as well as to ultrasound treatment with an amplitude of 50 and 70% for 5 and 10 min. The results indicated the same level of total phenolic content for pasteurized and sonicated samples for 10 min with an amplitude of 70%, while the highest level of l-ascorbic acid was recorded for sonicated samples with an amplitude of 70% for 10 min. pH of sonicated samples decreased with amplitude and treatment time while total soluble solids and titratable acidity increased with amplitude and time. Moreover, the results indicated the usefulness of juice sonication to enhance the inactivation of microorganisms. Thus, the high-power ultrasound treatment might represent a viable technique to replace the conventional thermal treatment in grape juice processing.

Internet-of-Things (IoT) represents a breakthrough for the current ICT market. In many IoT applications, sensors and actuators are distributed over very wide areas, sometimes not reached by terrestrial networks. In such scenarios, the satellite plays a significant role. In this paper, a Software-Defined Radio (SDR) -based satellite gateway for Internet-of-Remote-Things (IoRT) is proposed. The use of SDR allows to decrease equipment cost and provides higher flexibility. The proposed architecture has been implemented by using a standalone SDR platform and Commercial Off-The-Shelf (COTS) modules for covering the main terrestrial IoT standards. Extensive proof-of-concept results are presented and discussed. Uplink and downlink tests showed the correct functionality implementation and transmitted signal generation, while the integration tests allowed to assess the reliability of the end-to-end information processing. Reconfigurability tests confirmed the capability of the gateway of dynamically updating in real-time its protocol settings. The overall test results showed the validity of the proposed SDR-based gateway for IoRT applications.INDEX TERMS Internet of Remote Things (IoRT), Satellite Networking, Software-Defined Radio (SDR)

Precision hard turning (HT) gained more and more attention in the cutting industry in the last years due to continuous pressure of the global market for reducing costs, minimizing the environmental and health issues, and achieving a cleaner production. Therefore, dry cutting and minimal quantity lubrication (MQL) became widely used in manufacturing to meet the environmental issues with respect to harmful cutting fluids (CFs). Vegetable oils, in MQL machining, are a promising solutions to petroleum-based CFs; however, the effects and performance on surface roughness and tool wear in HT with ceramic inserts remain unclear. To address this limitation, hardened AIDI D2 steel and pure corn oil, rich in saturated and monounsaturated fatty acids, cheap and widely available, have been used to conduct dry and MQL experiments at different cutting speed and feeds. Results show that corn oil is suitable as cutting lubricant in HT, creating a strong anti-wear and anti-friction lubricating film which improves the roughness with 10–15% and tool life with 15–20%, therefore reducing costs. Best surface roughness values (Ra = 0.151 μm, Rz = 0.887 μm, Rpk = 0.261 μm) were obtained at 180 m/min and 0.1 mm/rev. The analysis of variance shows that corn oil has statistical significance on roughness, validating the results.

No abstract

Abstract. In theory and practice of management is well-known Lean approach about forms of waste from production processes (Muda) and the method VSM (Value Stream Map), one of the most effective methods for determining the activities generating value within industrial companies. It is also obvious concern of the specialists for performance measurement regardless of purview of the organizations. The literature review has shown that the link between performance indicators and the objectives of the companies is researched in detail. However, the correlation between indicators and the forms of waste that generate deviations from the setpoints is rather nature practical and it depends on the talent and managerial skills of those directing production processes. The paper presents the results of a applied study, performed by the authors, through which it was has sought to will create a system of performance indicators specific to manufacturing activity that to be a useful tool to quantify the losses and to determining ways to improve default losses.