No abstract

No abstract

The building sector is known to have a significant environmental impact, considering that it is the largest contributor to global greenhouse gas emissions of around 36% and is also responsible for about 40% of global energy consumption. Of this, about 50% takes place during the building operational phase, while around 10–20% is consumed in materials manufacturing, transport and building construction, maintenance, and demolition. Increasing the necessity of reducing the environmental impact of buildings has led to enhancing not only the thermal performances of building materials, but also the environmental sustainability of their production chains and waste prevention. As a consequence, novel thermo-insulating building materials or products have been developed by using both locally produced natural and waste/recycled materials that are able to provide good thermal performances while also having a lower environmental impact. In this context, the aim of this work is to provide a detailed analysis for the thermal characterization of recycled materials for building insulation. To this end, the thermal behavior of different materials representing industrial residual or wastes collected or recycled using Sardinian zero-km locally available raw materials was investigated, namely: (1) plasters with recycled materials; (2) plasters with natural fibers; and (3) building insulation materials with natural fibers. Results indicate that the investigated materials were able to improve not only the energy performances but also the environmental comfort in both new and in existing buildings. In particular, plasters and mortars with recycled materials and with natural fibers showed, respectively, values of thermal conductivity (at 20 °C) lower than 0.475 and 0.272 W/(m⋅K), while that of building materials with natural fibers was always lower than 0.162 W/(m⋅K) with lower values for compounds with recycled materials (0.107 W/(m⋅K)). Further developments are underway to analyze the mechanical properties of these materials.

No abstract

Development of technologies, materials, support systems, and coatings has made the integration of solar thermal systems into the building envelope increasingly possible. Solar thermal collectors can either be directly integrated, substituting conventional roof or façade covering materials, or constitute independent devices added to a roof or façade structure. Aimed at estimating the real effectiveness of building-integrated solar systems for domestic heat water (DHW) production or for heating integration, when horizontal or inclined pitches on buildings are not applicable, the authors analyze a case study with different scenarios, taking into account the issues connected to a highly urbanized context in the Mediterranean climate. A GIS model was used for estimating the energy balance, while the real producibility of the simulated systems was calculated by a dynamic hourly simulation model, realized according to ISO 52016. The savings in terms of primary energy needs obtained by installing solar thermal systems on the facade are presented, and the differences between the cases in which the system is used for DHW production only and for space heating too are distinguished and discussed. The evaluated potential is quantified in the absence of roof collectors, despite their high potential in the Mediterranean region, in order to better appreciate the effects induced by integrated facade systems.

In this study a theoretical analysis of a collector augmented by a bottom booster reflector is presented. An analytical model has been developed and used to estimate the solar irradiation passing through the transparent cover of a flat collector, both with and without a bottom reflector. The analytical model is based on the anisotropic sky model and takes into account a finite length system with different angular configurations and reciprocal shading and reflections between reflector and collector. Computer simulations have been carried out in order to find the optimum angles of the reflector with respect to the plane of the collector. Optimal inclinations of the collector and reflector for each month at 39° N latitude have been identified

No abstract

Airport activities can contribute to the emission of ultrafine particles (UFPs) in the environment. The aim of our study is to assess the airborne levels of UFPs in a military airport and in the surrounding area. Four outdoor air samplings were carried out inside a military airport during flight activities, twelve nearby the military airport, five in an urban area, and one in a rural area. We used a portable Electrical Low Pressure Impactor to detect the particle number size distribution as well as the number concentration. Particles were chemically analyzed by field emission scanning electron microscopy. Inside the military airport, we observed an inverse correlation with distance from flight activities. The median UFP count ranged 3.7 × 10 3 -2.9 × 10 4 particles/cm 3 , and the highest UFP count was 4.0 × 10 6 particles/cm 3 (during the taxi and take-off activities). Nearby the airport, UFP number concentrations were more elevated in the winter season and we did not observe a correlation with flight activities. Our results show a constant presence of UFPs regardless of the flight activities nearby the airport. Other anthropic sources may generate UFP concentrations significantly higher than those generated by airport activities.