O presente trabalho teve como objetivos realizar o levantamento qualitativo e quantitativo das espécies arbóreas da arborização das praças e das ruas localizadas no centro da cidade de São Joaquim, SC, bem como avaliar e detectar eventuais problemas na arborização, possibilitando fazer recomendações técnicas. Para isso, foi conduzido um censo das árvores presentes nas vias urbanas e nas praças do centro, sendo cada árvore identificada, determinada sua origem, mensurado seu espaço físico disponível e avaliado quanto a sua ocupação no espaço e condições gerais. Foi calculada a densidade relativa de cada espécie (DR) e verificado quais indivíduos necessitam ser substituídos, sendo realizadas sugestões de plantio de espécies nativas da região. Foram encontrados 195 indivíduos pertencentes a 35 espécies. Um total de 158 indivíduos, pertencentes a 25 espécies, eram exóticos, com predominância de Prunus serrulata Lindl. (DR=26,67%). Em 78% dos indivíduos foi encontrado ataque de pragas e doenças; em 41% houve algum tipo de injúria; em 65% foi constatado poda e 7,18% apresentaram interferência nos elementos urbanos. Sugere-se o enriquecimento da arborização da cidade com espécies nativas da região, adequadas ao espaço urbano existente e a substituição de indivíduos com injúrias graves, fitossanidade afetada e incompatibilidade da espécie com o espaço disponível.
ResumoO presente estudo teve como objetivo determinar a viabilidade técnica da produção de painéis aglomerados de misturas de fibras e maravalhas de Pinus spp por meio das propriedades físicas e mecânicas. A matéria-prima utilizada para a produção dos painéis foi composta por fibras retiradas do processo produtivo de MDF, maravalha coletada no processo de aplainamento da madeira, resina uréia-formaldeído e emulsão de parafina. O delineamento experimental envolveu cinco tratamentos homogêneos nas proporções de: 100 partes de fibras para 0 partes de maravalha (T1), 75:25 (T2), 50:50 (T3), 25:75 (T4) e 0:100 (T5). Foram produzidos três painéis por tratamento com 650 kg.m -3 de massa específica, 12% de resina, 1% de emulsão de parafina e ciclo de prensagem de 40 kg.cm -2 de pressão, 160 o C de temperatura por um tempo de 8 minutos. A determinação da massa específica, absorção de água, inchamento em espessura e tração perpendicular foram realizados de acordo com os procedimentos da ASTM (2006) AbstractThis study aimed to determine the technical feasibility of the production of particleboard from fibers and wood shaving of Pinus spp through physical and mechanical properties. The raw material used for producing panels was composed of fibers taken of the MDF process, wood shaving collected in the flattening process, urea formaldehyde resin and paraffin emulsion. The experiment involved 5 treatment homogeneous in the proportions: 100 parts of fibers to 0 parts of wood shavings (T1), 75:25 (T2), 50:50 (T3), 25:75 (T4) and 0: 100 (T5). 3 panels were produced by treatment with 650 kg.m -3 density, 12% resin, 1% paraffin emulsion and pressure of 140 kg.cm -2 , temperature of 160oC for 8 minutes. The determination of specific gravity, water absorption, and thickness swelling, tension perpendicular to surface were performed according to the procedures of ASTM (2006); the static bending test followed the procedures of DIN (1982) and screw withdrawal resistance the indications of ABNT (2013). With the verification of data normality and homogeneity of variance an analysis of variance was carried out and the Scott-Knott test at 95% probability. The results showed that the average values of dimensional stability of the panels were regular in relation to the reference standards. However, the increased amount of wood shaving in the panels caused a decrease in the mechanical properties, especially the modulus of elasticity in the static bending and in internal adhesion.
The finger-joints are the kind of top joints most used in wood blades to manufacture glued laminated timber (GLULAM) and present direct influence on their rigidity and final mechanical strength. Thus, the objective of this study was to evaluate the tensile strength parallel to grain with different compositions of reinforcements concentrated on finger-joints. Two geometries were used to execute the finger-joints and two species: Pinus taeda and Eucalyptus spp. The reinforcements were fabrics from glass or carbon fibers bonded with polyurethane structural adhesive. The treatments used were: "A-Glass", "A-Glass2", "A-Carbon", “A-Without reinforcement”, "B-Glass", "B-Glass2", "B-Carbon" and “B-Without reinforcement”, being "A" or "B", the geometries and "2", the number of layers of tissue. For statistical analysis, the Dunnett test was used at 95% confidence interval. The results showed that the execution of the unreinforced finger-joints decreased the tensile strength of the woods. For P. taeda, all the treatments were significantly inferior to the control (without finger-joints), and for Eucalyptus spp., only the treatment "A-Unreinforced" presented inferior performance to the control (without finger-joints), all others presented equivalent mechanical resistance to solid wood. It can be concluded that for the Eucalyptus spp. wood, the application of reinforcement on the structural finger-joints improves the tensile strength, equating to the solid wood.
A crescente utilização da madeira na construção civil coincide com o desenvolvimento de novos produtos que possibilitam uma construção mais rápida, econômica e com maior qualidade. Destacase entre esses produtos o painel CLT-Cross Laminated Timber. Este produto foi desenvolvido na Europa nas últimas décadas. O trabalho tem como objetivo realizar uma análise de custos de produção do painel CLT com os materiais convencionais utilizados na construção. Foi confeccionado um painel estrutural em tamanho real com 3 camadas com madeira reflorestada de Pinus taeda. Durante a produção a quantidade de produtos e tempo gastos para a fabricação de forma artesanal foram mensurados. A comparação de custos foi realizada em relação a alvenaria estrutural e a alvenaria de vedação. Notou-se que o painel CLT apresenta um custo de 37% menor que a alvenaria de vedação e de 18,5% menor que a alvenaria estrutural, indicando um grande potencial para a sua produção na região de Lages-SC. Palavras-chave: Painel autoportante, madeira laminada cruzada, compósito estrutural em madeira.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.