For an accurate multiscale property modelling of fractured crystalline geothermal reservoirs, an enhanced characterisation of the geometrical features and variability of the fracture network properties is an essential prerequisite. Combining regional digital elevation model analysis and local outcrop investigation, the study comprises the characterisation of the fracture pattern of a crystalline reservoir analogue in the Northern Odenwald, with LiDAR and GIS structural interpretation. This approach provides insights into the 3D architecture of the fault and fracture network, its clustering, and its connectivity. Mapped discontinuities show a homogeneous length distribution, which follows a power law with a −2.03 scaling factor. The connectivity of the fracture network is heterogenous, due to a fault control at the hectometric scale. Clustering is marked by long sub-vertical fractures at the outcrop scale, and strongly enhance heterogeneity around weathered fracture and fault corridors. The multi-variable dataset created within this study can be used as input data for accurate discrete fracture networks and fluid-flow modelling of reservoirs of similar type.

The understanding of fluid flow in faulted sandstones is based on a wide range of techniques. These depend on the multi-method determination of petrological and structural features, porous network properties and both spatial and temporal variations and interactions of these features. The question of the multi-parameter analysis on fluid flow controlling properties is addressed for an outcrop damage zone in the hanging wall of a normal fault zone on the western border of the Upper Rhine Graben, affecting the Buntsandstein Group (Early Triassic). Diagenetic processes may alter the original pore type and geometry in fractured and faulted sandstones. Therefore, these may control the ultimate porosity and permeability of the damage zone. The classical model of evolution of hydraulic properties with distance from the major fault core is nuanced here. The hydraulic behavior of the rock media is better described by a pluriscale model including: 1) The grain scale, where the hydraulic properties are controlled by sedimentary features, the distance from the fracture, and the impact of diagenetic processes. These result in the ultimate porous network characteristics observed. 2) A larger scale, where the structural position and characteristics (density, connectivity) of the fracture corridors are strongly correlated with both geo-mechanical and hydraulic properties within the damage zone.

Abstract. The crystalline basement is considered a ubiquitous and almost inexhaustible source of geothermal energy in the Upper Rhine Graben (URG) and other regions worldwide. The hydraulic properties of the basement, which are one of the key factors in the productivity of geothermal power plants, are primarily controlled by hydraulically active faults and fractures. While the most accurate in situ information about the general fracture network is obtained from image logs of deep boreholes, such data are generally sparse and costly and thus often not openly accessible. To circumvent this problem, an outcrop analogue study was conducted with interdisciplinary geoscientific methods in the Tromm Granite, located in the southern Odenwald at the northeastern margin of the URG. Using light detection and ranging (lidar) scanning, the key characteristics of the fracture network were extracted in a total of five outcrops; these were additionally complemented by lineament analysis of two different digital elevation models (DEMs). Based on this, discrete fracture network (DFN) models were developed to calculate equivalent permeability tensors under assumed reservoir conditions. The influences of different parameters, such as fracture orientation, density, aperture and mineralization, were investigated. In addition, extensive gravity and radon measurements were carried out in the study area, allowing fault zones with naturally increased porosity and permeability to be mapped. Gravity anomalies served as input data for a stochastic density inversion, through which areas of potentially increased open porosity were identified. A laterally heterogeneous fracture network characterizes the Tromm Granite, with the highest natural permeabilities expected at the pluton margin, due to the influence of large shear and fault zones.

Abstract. The crystalline basement is considered a ubiquitous and almost inexhaustible source of geothermal energy in the Upper Rhine Graben and other regions worldwide. The hydraulic properties of the basement, which are one of the key factors for the productivity of geothermal power plants, are primarily controlled by hydraulically active faults and fractures. While the most accurate in situ information about the general fracture network is obtained from image logs of deep boreholes, such data are generally sparse, costly and thus often not openly accessible. To circumvent this problem, an outcrop analogue study with interdisciplinary geoscientific methods was conducted in the Tromm Granite, located in the southern Odenwald at the northeastern margin of the URG. Using LiDAR scanning, the key characteristics of the fracture network were extracted in a total of five outcrops, additionally complemented by lineament analysis of two different digital elevation models. Based on this, discrete fracture network (DFN) models were developed to calculate equivalent permeability tensors under assumed reservoir conditions. The influence of different parameters, such as fracture orientation, density, aperture and mineralization was investigated. In addition, extensive gravity and radon measurements were carried out in the study area, allowing for more precise localization of fault zones with naturally increased porosity and permeability. Gravity anomalies served as input data for a stochastic density inversion, through which areas of increased open porosity were identified. A laterally heterogeneous fracture network characterizes the Tromm Granite, with the highest natural permeabilities expected at the pluton margin, due to the influence of large shear and fault zones.

Fracture network is a crucial element to address in any model of the thermo-hydro-mechanical behaviour of a reservoir rock. This study aims to provide quantified datasets and a further understanding of the critical parameters of the fracture network pattern in crystalline rocks. In the Northern Upper Rhine Graben, such rock units are targeted for multiple energy applications, from deep geothermal heat extraction to heat storage. Eleven outcrops were investigated with a combined LiDAR and 2D profiles analysis to extract faults and fracture network geometrical parameters, including length distribution, orientation, connectivity, and topology. These properties are used to decipher the structural architecture and estimate the flow properties of crystalline units. Fracture networks show a multi-scale power-law behaviour for length distribution. Fracture topology and orientation are mainly driven by both fault networks and lithology. Fracture apertures and permeability tensors were then calculated for two application case studies, including the stress field effect on aperture. Obtained permeabilities are in the range of those observed in the sub-surface in currently exploited reservoirs. The dataset provided in this study is thus suitable to be implemented in the modelling during the exploration stage of industrial applications involving fractured crystalline reservoirs.