Over the years, several approaches have been devised to widen the operating bandwidth, but most of them can only be triggered at high accelerations. In this work, we investigate a broadband energy harvester based on combination of non-linear stiffening effect and multimodal energy harvesting to obtain high bandwidth over wide range of accelerations (0.1 g–2.0 g). In order to achieve broadband behavior, a polymer based spring exhibiting multimodal energy harvesting is used. Besides, non-linear stiffening effect is introduced by using mechanical stoppers. At low accelerations (<0.5 g), the nearby mode frequencies of polymer spring contribute to broadening characteristics, while proof mass engages with mechanical stoppers to introduce broadening by non-linear stiffening at higher accelerations. The electromagnetic mechanism is employed in this design to enhance its output at low accelerations when triboelectric output is negligible. Our device displays bandwidth of 40 Hz even at low acceleration of 0.1 g and it is increased up to 68 Hz at 2 g. When non-linear stiffening is used along with multimodal energy-harvesting, the obtained bandwidth increases from 23 Hz to 68 Hz with percentage increment of 295% at 1.8 g. Further, we have demonstrated the triboelectric output measured as acceleration sensing signals in terms of voltage and current sensitivity of 4.7 Vg−1 and 19.7 nAg−1, respectively.

An integrated CMOS ultrawideband wireless telemetry transceiver for wearable and implantable medical sensor applications is reported in this letter. This high duty cycled, noncoherent transceiver supports scalable data rate up to 10 Mb/s with energy efficiency of 0.35 nJ/bit and 6.2 nJ/bit for transmitter and receiver, respectively. A prototype wireless capsule endoscopy using the proposed transceiver demonstrated in vivo image transmission of 640 × 480 resolution at a frame rate of 2.5 frames/s with 10 Mb/s data rate.

No abstract

Triboelectric nanogenerators (TENGs) have emerged as a potential solution for mechanical energy harvesting over conventional mechanisms such as piezoelectric and electromagnetic, due to easy fabrication, high efficiency and wider choice of materials. Traditional fabrication techniques used to realize TENGs involve plasma etching, soft lithography and nanoparticle deposition for higher performance. But lack of truly scalable fabrication processes still remains a critical challenge and bottleneck in the path of bringing TENGs to commercial production. In this paper, we demonstrate fabrication of large scale triboelectric nanogenerator (LS-TENG) using roll-to-roll ultraviolet embossing to pattern polyethylene terephthalate sheets. These LS-TENGs can be used to harvest energy from human motion and vehicle motion from embedded devices in floors and roads, respectively. LS-TENG generated a power density of 62.5 mW m−2. Using roll-to-roll processing technique, we also demonstrate a large scale triboelectric pressure sensor array with pressure detection sensitivity of 1.33 V kPa−1. The large scale pressure sensor array has applications in self-powered motion tracking, posture monitoring and electronic skin applications. This work demonstrates scalable fabrication of TENGs and self-powered pressure sensor arrays, which will lead to extremely low cost and bring them closer to commercial production.

This paper presents a novel data compression and transmission scheme for power reduction in Internet-of-Things (IoT) enabled wireless sensors. In the proposed scheme, data is compressed with both lossy and lossless techniques, so as to enable hybrid transmission mode, support adaptive data rate selection and save power in wireless transmission. Applying the method to electrocardiogram (ECG), the data is first compressed using a lossy compression technique with a high compression ratio (CR). The residual error between the original data and the decompressed lossy data is preserved using entropy coding, enabling a lossless restoration of the original data when required. Average CR of 2.1 × and 7.8 × were achieved for lossless and lossy compression respectively with MIT/BIH database. The power reduction is demonstrated using a Bluetooth transceiver and is found to be reduced to 18% for lossy and 53% for lossless transmission respectively. Options for hybrid transmission mode, adaptive rate selection and system level power reduction make the proposed scheme attractive for IoT wireless sensors in healthcare applications.

A novel double-gate (DG) tunneling field-effect transistor (TFET) with silicon–germanium (SiGe) Source is proposed to overcome the scaling limits of complementary metal–oxide–semiconductor (CMOS) technology and further extends Moore's law. The narrower bandgap of the SiGe source helps to reduce the tunneling width and improves the subthreshold swing and on-state current. Less than 60 mV/decade subthreshold swing with extremely low off-state leakage current is achieved by optimizing the device parameters and Ge content in the source. For the first time, we show that such a technology proves to be viable to replace CMOS for high performance, low standby power, and low power technologies through the end of the roadmap with extensive simulations.

This brief presents an on-off LC oscillator-based ultrawideband impulse radio (UWB-IR) transmitter for long-range application. A thorough theoretical analysis of the pulse generation is provided. Implemented in a 0.18-μm CMOS, the transmitter works in the UWB lower band of 3-5 GHz and consumes an ultralow average power of 236 μW at 1.8-V power supply. UWB pulses with a bandwidth of 2 GHz and 10-dB sidelobe suppression are generated. The transmitter can deliver a large differential output swing of 4.9 V under 100-Ω load with the highest power efficiency of 25.4% to date. It is targeted for wireless sensor network (WSNs) and wireless personal area network (WPAN) applications.Index Terms-CMOS IC, FCC spectral mask, impulse radio (IR), low data rate, low duty cycle, low power, pulse generator, ultrawideband (UWB), wireless.

A low power 60-GHz on-off-keying (OOK) receiver has been implemented in a commercial 90 nm RF CMOS process. By employing a novel on-chip antenna together with architecture optimization, the receiver achieves a sensitivity of 47 dBm at a bit-error rate (BER) of less than 10 3 . Using a commercial transmitter with transmit power of 1.5 dBm, a transmission distance of 5 cm can be achieved at 1.2 Gbps data rate. In this design, the on-chip antenna minimizes the packaging loss, while energy detection at RF allows architecture simplification. Both techniques contribute to the receiver's low power consumption of 51 mW, excluding test buffers. This leads to a bit energy efficiency of 28 pj/bit at 1.8 Gbps. The total die area is 3.8 mm 2 with the on-chip antenna occupying almost half of it.