No abstract

Three photocatalyst inks based on the redox dyes, Resazurin (Rz), Basic Blue 66 (BB66) and Acid Violet 7 (AV7, are used to assess the photocatalytic activities of a variety of different materials, such as commercial paint, tiles and glass and laboratory made samples of sol-gel coated glass and paint, which collectively exhibit a wide range of activities that cannot currently be probed by any one of the existing ISO tests. Unlike the ISO tests, the ink tests are fast (typically < 10 min), simple to employ and inexpensive. Previous work indicates that the Rz ink test at least correlates linearly with other photocatalytic tests such as the photomineralisation of stearic acid. The average time to bleach 90% of the key RGB colour component of the ink (red for Rz and BB66 inks) and green for AV7 ink) is determined, ca. 11% and ca 21%, respectively, which compare well with those reported for the current ISO tests. Additional work on commercial self-cleaning glass using an Rz ink showed that the change in the red component of the RGB image of the ink correlated linearly with that of the change of absorbance (at 608 nm) (as measured using UV/Vis spectroscopy) and the change in the a* component of the Lab colour analysis of the ink, as measured using diffuse reflectance spectroscopy. As a consequence, all three methods generate the same ttb(90).The advantages of the RGB digital image analysis method are discussed briefly.

The preparation and characterisation of a novel, water-proof, irreversible, reusable, UV-activated, O(2) sensitive, smart plastic film is described. A pigment, consisting of a redox dye, methylene blue (MB), and a sacrificial electron donor, DL-threitol, coated onto an inorganic support with semiconductor functionality, TiO(2), has been extruded in low-density polyethylene (LDPE). The blue-coloured indicator is readily photobleached in <90 s using UVA light (4 mW cm(-2)), whereby MB is converted to its colourless, leuco form, leuco-methylene blue (LMB). This form persists in the absence of oxygen, but is re-oxidised to MB in ~2.5 days in air under ambient conditions (∼21 °C, ~65% RH) within the O(2) smart plastic film. The rate of recovery is linearly dependent upon the ambient level of O(2). At the lower temperature of 5 °C, the kinetics of the photobleaching activation step is largely unchanged, whereas that of recovery is markedly reduced to t(1/2) = 36 h at 5 °C (cf. 9 h at 21 °C); the activation energy for the recovery step was calculated as 28 kJ mol(-1). The O(2)-sensitive recovery step was found to be moderately dependent upon humidity at 21 °C, but not significantly dependent upon humidity at 5 °C. The possible application of this type of indicator in food packaging is illustrated and discussed briefly.

Photochemical reactions employing TiO2 and carboxylic acids under dry anaerobic conditions led to several types of C–C bond-forming processes with electron-deficient alkenes. The efficiency of alkylation varied appreciably with substituents in the carboxylic acids. The reactions of aryloxyacetic acids with maleimides resulted in a cascade process in which a pyrrolochromene derivative accompanied the alkylated succinimide. The selectivity for one or other of these products could be tuned to some extent by employing the photoredox catalyst under different conditions. Aryloxyacetic acids adapted for intramolecular ring closures by inclusion of 2-alkenyl, 2-aryl, or 2-oximinyl functionality reacted rather poorly. Profiles of reactant consumption and product formation for these systems were obtained by an in situ NMR monitoring technique. An array of different catalyst forms were tested for efficiency and ease of use. The proposed mechanism, involving hole capture at the TiO2 surface by the carboxylates followed by CO2 loss, was supported by EPR spectroscopic evidence of the intermediates. Deuterium labeling indicated that the titania likely donates protons from surface hydroxyl groups as well as supplying electrons and holes, thus acting as both a catalyst and a reaction partner.

The rate of hydrogen evolution, r(H 2), due to the photocatalysed reforming of methanol, MeOH, is studied as a function of Pt loading on P25 TiO 2 both in the aqueous (at room temperature) and gas phase (at 100 o C). A similar study, using Pd on P25, has been reported earlier [M. Bowker et al. J. Catalysis, 2003, 217, 427-433] and a perimeter-based Metal-Support Interface (MSI) kinetic model used to interpret the results. Here a new kinetic model is introduced which appears to provide a better fit to all the r(H 2) vs wt% metal data sets, in which the rate of reaction is proportional to an extended area around each metal island, rather than its perimeter. A simple theoretical rationale is provided for this expanding photocatalytic area and overlap (EPAO) kinetic model in which each metal island forms an electric field with the surrounding TiO 2 so as to act as a sink for electrons photogenerated in the surrounding TiO 2 film, thereby allowing it to effect the reduction of water, leaving the remaining photogenerated holes to oxidise the methanol adsorbed on the TiO 2. Some support for this very simple kinetic and theoretical model is provided by the results of a brief study of the oxidation of soot deposited on and around a Pt 'dot' on a sol-gel TiO 2 film, in that, upon irradiation of this system a zone of activity is visibly revealed by the gradual disappearance of the soot around the Pt 'dot', the radius of which appears to be proportional to the radius of the metal 'dot'.

No abstract

A rapid, semi-quantitative, inexpensive method, using a simple digital scanner and an indicator ink, suitable for use in the laboratory, or in the field, for assessing the photocatalytic activity of commercial photocatalytic self-cleaning materials such as glass, is described. The repeatability of the current method is found to be high and better than many of the previously reported ISO photocatalyst tests.

No abstract