Objectives To compare the clinical performance of Scotchbond™ Universal Adhesive used in self- and total-etch modes and two-bottle Scotchbond™ Multi-purpose Adhesive in total-etch mode for Class 5 non-carious cervical lesions (NCCLs). Methods 37 adults were recruited with 3 or 6 NCCLs (>1.5 mm deep). Teeth were isolated, and a short cervical bevel was prepared. Teeth were restored randomly with Scotchbond Universal total-etch, Scotchbond Universal self-etch or Scotchbond Multi-purpose followed with a composite resin. Restorations were evaluated at baseline, 6, 12 and 24 months for marginal adaptation, marginal discoloration, secondary caries, and sensitivity to cold using modified USPHS Criteria. Patients and evaluators were blinded. Logistic and linear regression models using a generalized estimating equation were applied to evaluate the effects of time and adhesive material on clinical assessment outcomes over the 24 month follow-up period. Kaplan–Meier method was used to compare the retention between adhesive materials. Results Clinical performance of all adhesive materials deteriorated over time for marginal adaptation, and discoloration (p <0.0001). Both Scotchbond Universal self-etch and Scotchbond Multi-purpose materials were more than three times as likely to contribute to less satisfying performance in marginal discoloration over time than Scotchbond Universal total-etch. The retention rates up to 24 months were 87.6%, 94.9% and 100% for Scotchbond Multi-purpose and Scotchbond Universal self-etch and total-etch, respectively. Conclusions Scotchbond Universal in self- and total- etch modes performed similar to or better than Scotchbond Multipurpose, respectively. Clinical significance 24 month evaluation of a universal adhesive indicates acceptable clinical performance, particularly in a total-etch mode.

Purpose Candida albicans has been regarded as the most predominant oral fungal pathogen and the main cause of denture stomatitis. This study aimed to investigate C. albicans adherence to three types of denture base polymers: heat‐cured polymethylmethacrylate (PMMA), CAD‐CAM milled and 3D‐printed. The efficacy of four common disinfection techniques, glutaraldehyde, brushing, microwave irradiation, and Polident overnight tablets, were also examined. Material and methods Sixty blocks of pink acrylic specimens were fabricated from each polymer group. To investigate the C. albicans adherence, as well as the efficacy of different disinfection techniques on removing the yeast from the different materials, specimens were cultured within the fungal culture overnight followed by disinfection. The adhered C. albicans on the materials were then obtained by vortexing in phosphate buffered saline (PBS), and the numbers of the yeast in the suspensions were evaluated by measuring the optical density and/or colony‐forming units on agar plates. Data were expressed as mean ± SEM (standard error of the mean). Statistical differences were evaluated by one‐way analysis of variance (ANOVA) followed by the post hoc Tukey HSD tests. Results Significant differences in C. albicans adherence to the three polymers were noted. CAD‐CAM milled and heat‐cured PMMA showed significantly less C. albicans adherence compared with 3D printed PMMA. No significant difference was noted between milled and heat‐cured PMMA. In the disinfection test, microwave irradiation, mechanical brushing, and Polident tablets were found to be effective in removing fungal attachment on the different denture materials, while glutaraldehyde was found to be the least effective. Conclusion C. albicans adherence to the polymers varies greatly based on the types of PMMA. 3D‐printed had the highest fungal biofilm attachment. Microwave irradiation, mechanical brushing, and Polident overnight tablets had comparable results in removing C. albicans from all types of PMMA, while glutaraldehyde was not as effective.

The prefabricated attachments had superior retention than the cast groups over time. Reduced dimension did not reduce the retention when compared to the cast group.

Extreme residual ridge resorption is a challenging clinical situation for the fabrication of complete dental prostheses. Computer-aided design and computer-aided manufacturing (CAD/CAM) complete dentures have been shown to have superior fit and material strength to conventionally fabricated dentures, but no clinical protocols have been described for cases of extreme residual ridge resorption. This report describes a workflow combining conventional and novel techniques for CAD/CAM complete dentures fabrication for atrophic alveolar ridges and demonstrates that a CAD/CAM workflow is an effective tool for solving this complex situation.

Hypodontia is one of the most common developmental problems of human dentition. The treatment of missing maxillary central incisors is always a challenging task, often requiring a multidisciplinary approach. This case report describes such a multidisciplinary approach for a female patient with congenitally missing maxillary central incisors and class II division 1 occlusion. Significant horizontal overlap was present with class II division 1 occlusion in a patient with a history of cleft palate. Implant therapy was thereby not an option. Orthodontic treatment was provided to decrease the horizontal overlap and reposition the teeth. Esthetic crown lengthening was performed and monolithic lithium disilicate crowns were placed. Critical analysis of the treatment plan through cooperation among specialists is required to obtain the ideal result. Orthodontic treatment may be necessary to close or gain more space, followed by implant placement (if acceptable), and restorative treatment. It is important to create the treatment plan through a multidisciplinary approach involving orthodontists, surgeons, and restorative specialists before initiating treatment.