No abstract

No abstract

Hydromechanical and structural properties of compacted loess have a significant impact on the stability and reliability of subbase and subgrade, which needs to be quickly determined in the field and laboratory. Hence, an electrical resistivity method was used to characterize the hydromechanical and structural properties of compacted loess during constant rate of strain compression. In the present work, compacted loess samples with a dry density of 1.7 g/cm3, a diameter of 64 mm, a height of 10 mm and different water content ranging from 5–25% were prepared. The constant rate of strain (CRS) tests were conducted by a developed oedometer cell equipped with a pair of horizontal circular electrodes (diameter of 20 mm) and vertical rectangular electrodes (width of 3.5 mm) to determine the electrical resistivity of compacted loess. The results showed that as average water content increases, plastic compression indices increase from 0.220 to 0.350 and the elastic compression indices increase from 0.0152 to 0.030, but they decrease to 0.167 and 0.010 and yield stress decreases from 381.28 kPa to 72.35 kPa. Moreover, as vertical strain increases, the variation trend of average formation factor and average shape factor for the lower water content decreases but increases for the maximum water content, and the anisotropy index first decrease and then tend to increase slightly, which indicates that the structural properties of unsaturated and saturated samples during compression exhibits different trend and the anisotropy of samples tend to be stable as vertical strain increases. As the water content increases, the average formation factor and average shape factor decrease, but the anisotropy index first decreases then increases, suggesting that water content has a significant impact on these electrical indices. More important, The coefficients of average formation factor decrease from 33.830 to −1.698 and the coefficients of average shape factor decrease from 8.339 to −0.398 as water content increases, whereas there is less variation for the coefficient of anisotropic index with a value of 2.190. An equation correlating average formation factor and water content and vertical strain is regressed to characterize the hydromechanical properties of compacted loess by measuring its impedance, which can be used to evaluate the stability of compacted loessic ground and subgrade.

No abstract

No abstract

No abstract

As a new technique, a fixed geogrid in a geogrid-reinforced and pile-supported (GRPS) embankments has been used to reduce the total and differential settlement. To investigate the load transfer mechanism of the fixed geogrid technique of a GRPS embankment, three discrete element method (DEM) models of pile-supported embankments were established, including an unreinforced embankment, a geogrid reinforced embankment, and a fixed geogrid reinforced embankment. The efficacy of the pile, the evolution law of the contact force chain and the axial force of the reinforcement, and the microscopic load-bearing structure of the soil were investigated. Numerical simulation results showed that the embankment self-weight and surcharge load were transferred to the pile through the soil arching and tensile membrane effect. The settlement could be effectively reduced via the addition of the reinforcement, and the fixed geogrid technique was more conducive to improving the load-bearing ratio of the pile than the traditional reinforcement technique. Compared with the traditional technique of a GRPS embankment, the fixed geogrid technique had a better effect on reducing the total and differential settlement. With the increase in the surcharge load and the settlement of the soft subsoil, the reinforcement transferred a greater load to the pile. The results also showed that the stress of the embankment fill was concentrated at the pile top in all three models. The GRPS embankment with a fixed geogrid technique had a lower soil stress concentration than the other two cases. The contact force chain and stress in the embankment also showed that the reformation of the microscopic load-bearing system of the embankment fill was the internal mechanism that caused the development of the soil arching and the redistribution of stress. Furthermore, the evolution of the fabric parameters in the arching area could reflect the evolution of the soil arching structure. In the fixed geogrid case, the proportion of the load transferred to the pile from the soil arching effect was reduced, and the vertical load transferred to the pile top by the tensile membrane effect accounted for 22–28% in this study. Under the combined effect of the tensile membrane and the soil arching, the efficacy of the pile could increase by 10%.

Geogrids have been extensively used in subgrade construction for stabilization purposes of unconfined ballast. Based on well-calibrated microparameters, a series of geogrid-reinforced ballast models with different geogrid sizes and particular structures were developed to reproduce the mechanical behavior of the geogrid under pull-out load in this paper. And the rationality of the DEM model is verified by comparing the evolution law pull-out force measured by laboratory tests and numerical simulations under comparable conditions. Moreover, the macro pull-out force and the internal force distribution of the geogrid were analyzed, and the contact force statistical zones of the particle system were divided accurately according to the results. Meanwhile, both the force transfer mechanism in the geogrid-ballast interface and the sectionalized strain of the geogrid were discussed. And results unveil that the pull-out load is transmitted along the longitudinal ribs to the transverse ribs, and nearly 90% of the load is transmitted to the contact network (in statistical zone 1) in front of the first transverse rib, resulting in strong interlocking between the particles occurs in statistical zone 1. And the second transverse rib is the strength dividing line between strong and weak contact forces. Then, additional pull-out tests on the control groups were conducted, and the sectionalized strain of the geogrid and the peak pull-out force, as well as the energy dissipation were systematically analyzed. In addition, the proposed method used in simulation holds much promise for better understanding of the reinforcement mechanism and further optimizing the performance of geogrid-reinforced structures.