Peroxide radical treatments of a perfluorinated ionomer used in polymer electrolyte membrane
(PEM) fuel cells and its small molecule analogues were carried out, along with analysis of the resultant products.
Molecules containing terminal carboxylic acids degraded at least 1 order of magnitude faster than noncarboxylate
materials; all of the systems did show peroxide-initiated degradation nonetheless. Product analysis suggests that
terminal carboxylic acids react according to a sequential chain shortening, consistent with previous studies. Cleavage
of side chains from both polymer and model compounds was also observed to be important and in fact may be
the dominate pathway in low carboxyl content commercial PEM membranes, based on the following comparison
of reactivity and concentration. The relative reactivities of carboxylic chain ends and ether linkages is approximately
500, as calculated using model compounds fluoride generation rates. Commercial perfluorosulfonic acid (PFSA)
products contain minimal carboxylic acid end groups, and the side chain concentrations are of 2−3 orders of
magnitude higher than carboxylic acid end groups.
Time-resolved adsorption behavior of a human immunoglobin G (hIgG) protein on a hydrophobized gold
surface is investigated using multitechniques: quartz crystal microbalance/dissipation (QCM-D) technique;
combined surface plasmon resonance (SPR) and Love mode surface acoustic wave (SAW) technique; combined
QCM-D and atomic force microscopy (AFM) technique. The adsorbed hIgG forms interfacial structures
varying in organization from a submonolayer to a multilayer. An “end-on” IgG orientation in the monolayer
film, associated with the surface coverage results, does not corroborate with the effective protein thickness
determined from SPR/SAW measurements. This inconsistence is interpreted by a deformation effect induced
by conformation change. This conformation change is confirmed by QCM-D measurement. Combined
SPR/SAW measurements suggest that the adsorbed protein barely contains water after extended contact
with the hydrophobic surface. This limited interfacial hydration also contributed to a continuous conformation
change in the adsorbed protein layer. The viscoelastic variation associated with interfacial conformation
changes induces about 1.5 times overestimation of the mass uptake in the QCM-D measurements. The
merit of combined multitechnique measurements is demonstrated.
We show the theoretical and experimental combination of acoustic and optical methods for the in situ quantitative evaluation of the density, the viscosity and the thickness of soft layers adsorbed on chemically tailored metal surfaces. For the highest sensitivity and an operation in liquids, a Love mode surface acoustic wave (SAW) sensor with a hydrophobized gold coated sensing area is the acoustic method, while surface plasmon resonance (SPR) on the same gold surface as the optical method is monitored simultaneously in a single set-up for the real-time and label-free measurement of the parameters of adsorbed soft layers, which means for layers with a predominant viscous behavior. A general mathematical modeling in equivalent viscoelastic transmission lines is presented to determine the correlation between experimental SAW signal shifts and the waveguide structure including the presence of the adsorbed layer and the supporting liquid from which it segregates. A methodology is presented to identify from SAW and SPR simulations the parameters representatives of the soft layer. During the absorption of a soft layer, thickness or viscosity changes are observed in the experimental ratio of the SAW signal attenuation to the SAW signal phase and are correlated with 2 the theoretical model. As application example, the simulation method is applied to study the thermal behavior of physisorbed PNIPAAm, a polymer whose conformation is sensitive to temperature, under a cycling variation of temperature between 20 and 40• C. Under the assumption of the bulk density and the bulk refractive index of PNIPAAm, thickness and viscosity of the film are obtained from simulations; the viscosity is correlated to the solvent content of the physisorbed layer.3
A dual temperature-responsive triblock polymer (Poly(N-isopropyl acrylamide)-block-poly(N,N-dimethyl acrylamide)-block-poly(acrylamide-co-acrylonitrile) (P(AM-co-AN)-b-PDMA-b-PNIPAM) (NDAA) was obtained by sequential reversible addition–fragmentation chain transfer (RAFT) polymerization ,with the uncharged UCST temperature-sensitive block P (AM-co-AN) and the...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.