No abstract

Background Fuzhong buffalo, a native breed of Guangxi Zhuang Autonomous Region, is traditionally used as a draft animal to provide farm power in the rice cultivation. In addition, the Fuzhong buffalo also prepared for the bullfighting festival organized by the locals. The detection of the selective signatures in its genome can help in elucidating the selection mechanisms in its stamina and muscle development of a draft animal. Results In this study, we analyzed 27 whole genomes of buffalo (including 15 Fuzhong buffalo genomes and 12 published buffalo genomes from Upper Yangtze region). The ZHp, ZFst, π-Ratio, and XP-EHH statistics were used to identify the candidate signatures of positive selection in Fuzhong buffalo. Our results detected a set of candidate genes involving in the pathways and GO terms associated with the response to exercise (e.g., ALDOA, STAT3, AKT2, EIF4E2, CACNA2D2, TCF4, CDH2), immunity (e.g., PTPN22, NKX2-3, PIK3R1, ITK, TMEM173), nervous system (e.g., PTPN21, ROBO1, HOMER1, MAGI2, SLC1A3, NRG3, SNAP47, CTNNA2, ADGRL3). In addition, we also identified several genes related to production and growth traits (e.g., PHLPP1, PRKN, MACF1, UCN3, RALGAPA1, PHKB, PKD1L). Our results depicted several pathways, GO terms, and candidate genes to be associated with response to exercise, immunity, nervous system, and growth traits. Conclusions The selective sweep analysis of the Fuzhong buffalo demonstrated positive selection pressure on potential target genes involved in behavior, immunity, and growth traits, etc. Our findings provided a valuable resource for future research on buffalo breeding and an insight into the mechanisms of artificial selection.

Peroxisome-proliferator-activated receptor gamma (PPARγ) is a key transcription factor that controls adipocyte differentiation and energy in mammals. Therefore, PPARγ is a potential factor influencing animal growth traits. This study primarily evaluates PPARγ as candidate gene for growth traits of cattle and identifies potential molecular marker for cattle breeding. Per previous studies, PPARγ mRNA was mainly expressed at extremely high levels in adipose tissues as shown by quantitative real-time polymerase chain reaction analysis. Three novel SNPs of the bovine PPARγ gene were identified in 514 individuals from six Chinese cattle breeds: SNP1 (AC_000179.1 g.57386668 C > G) in intron 2 and SNP2 (AC_000179.1 g.57431964 C > T) and SNP3 (AC_000179.1 g.57431994 T > C) in exon 7. The present study also investigated genetic characteristics of these SNP loci in six populations. Association analysis showed that SNP1 and SNP3 loci significantly affect weaning growth traits, especially body weight of Nanyang cattle. These results revealed that SNP1 and SNP3 are potential molecular markers for cattle breeding.

As a stimulating point in acupuncture, acupoint has unique microcirculatory features, and its dynamics vary greatly depending on health status. Acupoint sensitization is defined as the transformation of an acupoint from a “silenced status” (healthy) to an “activated status” (disease). Our previous study demonstrated that acupoint sensitization is associated with an increase in the level of local blood perfusion. However, the structural changes in microcirculation during acupoint sensitization have yet to be elucidated because the high‐resolution microcirculation imaging of acupoints has been difficult to obtain. In this study, the structural changes in microcirculation at the Zusanli (ST36), Yanglingquan (GB34) and nonacupoint sites on days 0, 7 and 21 were dynamically observed during acupoint sensitization in an experimental knee osteoarthritis mouse model by using optical‐resolution photoacoustic microscopy. The results showed that no significant differences in microvessel density, the distribution of vessel diameters or vascular tortuosity were observed at the GB34, ST36 or nonacupoint sites among days 0, 7 and 21. We proposed that acupoint sensitization may not be associated with the structural changes in microcirculation and that the microcirculatory changes during acupoint sensitization are more likely to be functional. The functional characteristics of the sensitized acupoints warrant further investigation.

No abstract

A digitizer guided manual/automatic control system of cold rolling mill was designed in order to realize the cold rolling of seamless steel pipes with complicated outline. The system has the functions of local real-time monitoring and remote supervision. The operating principle and the structure of the control system were introduced. The digitizer and G code were used to program and the fitting and interpolation method was adopted for the smoothing process of the trajectory, which was recorded during the teaching process. The steel pipes produced by the machining playback have good quality. Practices show that this system is full function and has good reliability.