The in vivo intervertebral range of motion (ROM) is an important predictor for spinal disorders.While the subaxial cervical spine has been extensively studied, the motion characteristics of the occipito-atlantal (C0-1) and atlanto-axial (C1-2) cervical segments were less reported due to technical difficulties in accurate imaging of these two segments. In this study, we investigated the intervertebral ROMs of the entire cervical spine (C0-T1) during in vivo functional neck motions of asymptomatic human subjects, including maximal flexion-extension, left-right lateral bending, and left-right axial torsion, using previously validated dual fluoroscopic imaging and model registration techniques. During all neck motions, C0-1, similar to C7-T1, was substantially less mobile than other segments and always contributed less than 10% of the cervical rotations. During the axial rotation of the neck, C1-2 contributed 73.2±17.3% of the cervical rotation, but each of other segments contributed less than 10% of the cervical rotation. During both lateral bending and axial torsion neck motions, regardless of primary or coupled motions, the axial torsion ROM of C1-2 was significantly greater than its lateral bending ROM (p<0.001), whereas the opposite *

BackgroundCrocin (CRO), chlorogenic acid (CGA), geniposide (GEN), and quercetin (QUE) are all natural compounds with anti-obesity properties, in particular, hypolipidemic effects, which have been widely used for the treatment of obesity-related metabolic diseases. However, it is not yet known whether these compounds interact synergistically. Here, we investigated the effects and molecular mechanisms of CRO, CGA, GEN, QUE, and a combination of all four compounds (CCGQ), on lipid accumulation in human hepatoma (HepG2 cells).MethodsThe optimal concentration of CRO, CGA, GEN, QUE to stimulate HepG2 cells proliferation was determined using MTT assay. HepG2 cells were pretreated with 10 μmol/L simvastatin, 1 μmol/L CRO, 30 μmol/L CGA, 10 μmol/L GEN, 10 μmol/L QUE, and CCGQ (a combination of 1 μmol/L CRO, 30 μmol/L CGA, 10 μmol/L GEN, and 10 μmol/L QUE) for 24 or 48 h. Oil red O staining and extracellular TC and TG levels were detected. The RT-PCR was used to observe on cholesterol metabolism-related gene expression. Immunocytochemistry and western-blot assayed the 3-hydroxy-3-methylglutaryl-coenzyme (HMGCR) protein expression in HepG2 cells.ResultsCompared to those of control, we demonstrated that treating HepG2 cells for 48 h with CCGQ resulted in a strong synergistic effect, causing a marked decrease in lipid deposition in comparison to individual treatments, in both triglyceride and total cholesterol (CRO, 5.74- and 1.49-folds; CGA, 3.38- and 1.12-folds; GEN, 4.04- and 1.44-folds; QUE, 3.36- and 1.24-folds; simvastatin, 5.49- and 1.83-folds; and CCGQ, 7.75- and 2.20-folds), and Oil red O staining assays. In addition, CCGQ treatment increased ATP-binding cassette transporter (ABCA1), cholesterol 7α-hydroxylase (CYP7A1), and AMP-activated protein kinase 2α (AMPKα2) mRNA expression, while decreasing sterol regulatory element binding protein 2 (SREBP2), and liver X receptor alpha (LXRα) mRNA expression. Notably, CCGQ was more effective in decreasing HMGCR expression than the individual treatments.ConclusionThe CCGQ combination has potential, both as a complementary therapy for hyperlipemia, and in preventing further obesity-related complications.

Purpose To investigate the in vivo femoral condyle motion and synergistic function of the ACL/PCL along the weightbearing knee flexion. Methods Twenty-two healthy human knees were imaged using a combined MRI and dual fluoroscopic imaging technique during a single-legged lunge (0°-120°). The medial and lateral femoral condyle translation and rotation (measured using geometric center axis-GCA), and the length changes of the ACL/PCL were analyzed at: low (0°-30°), mid-range (30°-90°) and high (90°-120°) flexion of the knee. Results At low flexion (0°-30°), the strains of the ACL and the posterior-medial bundle of the PCL decreased. The medial condyle showed anterior translation and lateral condyle posterior translation, accompanied with a sharp increase in external GCA rotation (internal tibial rotation). As the knee continued flexion in mid-range (30°-90°), both ACL and PCL were slack (with negative strain values). The medial condyle moved anteriorly before 60° of flexion and then posteriorly, accompanied with a slow increase of GCA rotation. As the knee flexed in high flexion (90°-120°), only the PCL had increasingly strains. Both medial and lateral condyles moved posteriorly with a rather constant GCA rotation. Conclusions The ACL and PCL were shown to play a reciprocal and synergistic role during knee flexion. Mid-range reciprocal anterior-posterior femoral translation or laxity corresponds to minimal constraints of the ACL and PCL, and may represent a natural motion character of normal knees. The data could be used as a valuable reference when managing the mid-range "instability" and enhancing high flexion capability of the knee after TKAs. Level of evidence Level IV.

No abstract

No abstract

No abstract

No abstract

Using large femoral heads in total hip arthroplasty (THA) has been widely advocated to improve the function and longevity of the components. However, increasing the head size has been shown to accelerate polyethylene liner wear. Few studies have investigated the effect of other important structural parameters (such as polyethylene liner thickness, metal cup size, head‐liner conformity, loading conditions, etc.) on the biomechanical functions of the THAs. In this study, an analytical model was used to evaluate the polyethylene liner wear characteristics of the THAs (defined using a biomechanical wear factor) with various structural parameters of the THAs and loading conditions. For all the THA systems examined in this study, under the same loading conditions, a larger head leads to increasing contact areas, lower contact stresses, and higher biomechanical wear factors. When the head size is fixed, a decrease in the polyethylene liner thickness or a decrease in the head‐liner conformity leads to higher peak contact stresses and smaller contact areas and consequently, lower biomechanical wear factors. This study provides a parametric analysis tool for the optimal design/selection of the THA systems and for prediction of early effects of various structural parameters on the biomechanical function (such as contact stresses) and longevity (such as polyethylene liner wear) of the THA systems.