The sensitivity of a nanoscale crack-based sensor is enhanced markedly by modulating the crack depth. The crack-depth-propagated sensor exhibits ≈16 000 gauge factor at 2% strain and a superior signal-to-noise ratio of ≈35, which facilitates detection of target signals for voice-pattern recognition.

Owing to the growing demand for highly integrated electronics, anisotropic heat dissipation of thermal management material is a challenging and promising technique. Moreover, to satisfy the needs for advancing flexible and stretchable electronic devices, maintaining high thermal conductivity during the deformation of electronic materials is at issue. Presented here is an effective assembly technique to realize a continuous array of boron nitride (BN) nanosheets on tetrahedral structures, creating 3D thermal paths for anisotropic dissipation integrated with deformable electronics. The tetrahedral structures, with a fancy wavy shaped cross‐section, guarantee flexibility and stretchability, without the degradation of thermal conductivity during the deformation of the composite film. The structured BN layer in the composites induces a high thermal conductivity of 1.15 W m−1 K−1 in the through‐plane and 11.05 W m−1 K−1 in the in‐plane direction at the low BN fraction of 16 wt%, which represent 145% and 83% increases over the randomly mixing method, respectively. Furthermore, this structured BN composite maintains thermal dissipation property with 50% strain of the original length of composite. Various electronic device demonstrations provide exceptional heat dissipation capabilities, including thin film silicon transistor and light‐emitting diode on flexible and stretchable composite, respectively.

Bioelectronics needs to continuously monitor mechanical and electrophysiological signals for patients. However, the signals always include artifacts by patients’ unexpected movement (such as walking and respiration under approximately 30 hertz). The current method to remove them is a signal process that uses a bandpass filter, which may cause signal loss. We present an unconventional bandpass filter material—viscoelastic gelatin-chitosan hydrogel damper, inspired by the viscoelastic cuticular pad in a spider—to remove dynamic mechanical noise artifacts selectively. The hydrogel exhibits frequency-dependent phase transition that results in a rubbery state that damps low-frequency noise and a glassy state that transmits the desired high-frequency signals. It serves as an adaptable passfilter that enables the acquisition of high-quality signals from patients while minimizing signal process for advanced bioelectronics.

Highly sensitive temperature sensors are designed by exploiting the interparticle distance-dependent transport mechanism in nanocrystal (NC) thin films based on a thermal expansion strategy. The effect of ligands on the electronic, thermal, mechanical, and charge transport properties of silver (Ag) NC thin films on thermal expandable substrates of poly(dimethylsiloxane) (PDMS) is investigated. While inorganic ligand-treated Ag NC thin films exhibit a low temperature coefficient of resistance (TCR), organic ligandtreated films exhibit extremely high TCR up to 0.5 K −1 , which is the highest TCR exhibited among nanomaterial-based temperature sensors to the best of the authors' knowledge. Structural and electronic characterizations, as well as finite element method simulation and transport modeling are conducted to determine the origin of this behavior. Finally, an all-solution based fabrication process is established to build Ag NC-based sensors and electrodes on PDMS to demonstrate their suitability as low-cost, high-performance attachable temperature sensors.

No abstract

Although sensitivity and durability are desirable in a sensor, both of them cannot be easily achieved. Site-specific and effective signal acquisition on the limited area of a sensor inevitably allows fatigue accumulation and contamination. For example, an ultrasensitive nanoscale-crack-based sensor for detecting a mechanical stimulus with tremendous sensitivity (a gauge factor greater than 2000 under 2% strain), yet limited durability (up to a few thousand stretching cycles in tensile tests) has been presented previously. Herein, we suggest a simple yet robust nanoscale-crack-based sensor that achieves remarkable durability through the use of a self-healable polymer. The self-healable polymer helps the crack gap recover and maintain high stability for 1 million cycles under 2% strain. Moreover, site-specific recovery with infrared light irradiation was demonstrated with monolithic arrayed sensors. The proposed strategy provides a unique solution to achieving highly enhanced durability and high mechanosensitivity, which are typically incompatible.

Demands for precise health information tracking techniques are increasing, especially for daily dietry requirements to prevent obesity, diabetes, etc. Many commercially available sensors that detect dynamic motions of the body lack accuracy, while novel strain sensors at the research level mostly lack the capability to analyze measurements in real life conditions. Here, a stretchable, patch‐type calorie expenditure measurement system is demonstrated that integrates an ultrasensitive crack‐based strain sensor and Bluetooth‐enabled wireless communication circuit to offer both accurate measurements and practical diagnosis of motion. The crack‐based strain gauge transformed into a pop‐up‐shaped structure provides reliable measurements and broad range of strain (≈100%). Combined with the stretchable analysis circuit, the skin attachable tool translates variation of the knee flexion angle into calorie expenditure amount, using relative resistance change (R/R0) data from the flexible sensor. As signals from the knee joint angular movement translates velocity and walking/running behavior, the total amount of calorie expenditure is accurately analyzed. Finally, theoretical, experimental, and simulation analysis of signal stability, dynamic noises, and calorie expenditure calculation obtained from the device during exercise are demonstrated. For further applications, the devices are expected to be used in broader range of dynamic motion of the body for diagnosis of abnormalities and for rehabilitation.

No abstract