The Zero Valent Iron (ZVI) is the material most commonly used for permeable reactive barriers (PRB). For technical and economic reasons, hoter reactive substances usable in alternative to ZVI are investigated. The present study takes into account a vegetable fibers, the cabuya, investigating its capacity to retain heavy metals. The capacity of the cabuya fibers to adsorb heavy metals was verified in laboratory, by batch and column tests. The batch tests were carried out with cabuya and ZVI, using copper (Cu), zinc (Zn), cadmium (Cd) and lead (Pb). The results obtained by the cabuya fibers showed a very high adsorption capacity of heavy metals and resulted very similar to those obtained for the broom fibers in a previous study. The high value of the absorption capacity of the cabuya fibers was also confirmed by the analogous comparison made with the results of the batch tests carried out with ZVI. Column tests, using copper, zinc and cadmium, allowed to determine for the cabuya fibers the maximum removal percentage of the heavy metals considered, the corresponding times and the time ranges of the release phase. For each metal considered, for a given length and three different times, the constant of degradation of cabuya fibers was determined, obtaining values very close to those reported for broom fibers. The scalar behavior of heavy metal removal percentage was verified. An electron microscope analysis allowed to compare, by SEM images, the characteristics of the cabuya and broom fibers. Finally, to investigate the chemical structure of cabuya and broom fibers, the FTIR technique was used, obtaining their respective infrared spectra.

A series of experimental batch tests has been carried out with the aim of improving the knowledge of fundamental processes related to the fate and behavior of heavy metals that can be of environmental concern in groundwater. The analysis of contaminants (i.e., Cu, Zn, Cd and Pb) dynamics in different environmental compartments is specifically addressed by comparing the removal efficiencies of different types of reactive materials, three natural (i.e., vegetal fibers, natural limestone and natural zeolite) and one synthetic (i.e., synthetic zeolite). Results stemming from these reactive media has been compared with the outcomes related to the same test performed using zero valent iron which is the reactant usually employed for heavy metals remediation. All tested reactants exhibited important removal percentages, even larger than 90% in most cases, achieved in a contact time ranging between about 12 h and slightly longer than a day (i.e., 30 h). Maximum adsorption percentages are observed for pH ranging between 4 and 8 for all tested materials and contaminants. Our findings provided relevant evidence, to both researchers and technicians, on the competitiveness of the explored alternative mediums with respect to the classical reactants usually employed for heavy metals remediation.

The formation and hydrogen sorption properties of the NaMgH3 perovskite/type hydride have been examined. Samples were mechanically ball milled under argon for 2, 5 and 15 h; then characterized by X-ray diffraction (XRD), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) coupled with a mass spectrometer (MS). Lattice parameters and cell volume of the main NaMgH3 phase increase as a function of milling. Dehydrogenation proceeded in two-step reactions for the NaMgH3. The maximum amount of released hydrogen was achieved for the 2 h milled NaMgH3 hydride accounting for 5.8 wt.% of H2 from 287 °C to 408 °C. Decomposed NaMgH3 samples were reversibly hydrogenated under 10 bar H2 at ~200 °C.

The memristor is the fourth fundamental element in the electronic circuit field, whose memory and resistance properties make it unique. Although there are no electronic solutions based on the memristor, interest in application development has increased significantly. Nevertheless, there are only numerical Matlab or Spice models that can be used for simulating memristor systems, and designing is limited to using memristor emulators only. A memristor emulator is an electronic circuit that mimics a memristor. In this way, a research approach is to build discrete-component emulators of memristors for its study without using the actual models. In this work, two reconfigurable hardware architectures have been proposed for use in the prototyping of a non-linearity memristor emulator: the FPAA (Field Programing Analog Arrays) and the FPGA (Field Programming Gate Array). The easy programming and reprogramming of the first architecture and the performance, high area density, and parallelism of the second one allow the implementation of this type of system. In addition, a detailed comparison is shown to underline the main differences between the two approaches. These platforms could be used in more complex analog and/or digital systems, such as neural networks, CNN, digital circuits, etc.

No abstract