We investigate the potential of Brillouin Light Scattering (BLS) Microspectroscopy for fast non-invasive all-optical assessment of the mechanical properties of viscose fibers and bleached softwood pulp. Using an optimized Brillouin spectrometer, we demonstrate fast spatial mapping of the complex longitudinal modulus over extended areas ([ 100 lm). Our results reveal that while the softwood pulp has a relatively uniform moduli, the viscous fibers have significant spatial heterogeneous in the moduli. Specifically, the viscose fibers exhibited a regular pattern of increasing and decreasing modulus normal to the fiber axis. The potential influence of a locally changing refractive index is investigated by holographic phase microscopy and ruled out. We discuss our results in light of the anisotropic mechanical properties of the fibers and are able to estimate the relative difference between the modulus along the fiber axis and that perpendicular to it. Results are presented alongside reference measurements of the quasi-static mechanical properties transverse to the fiber axes obtained using AFM-nanoindentation which reveal a similar trend, hinting at the potential usefulness of BLS for mechanical characterization applications. However, more detailed investigations are called for to uncover all the factors influencing the measured high-frequency BLS modulus and its significance in relation to physical properties of the fiber that may be of practical interest.

Talc is a van der Waals and naturally abundant mineral with the chemical formula Mg3Si4O10(OH)2. Two-dimensional (2D) talc could be an alternative to hBN as van der Waals dielectric in 2D heterostructures. Furthermore, due to its good mechanical and frictional properties, 2D talc could be integrated into various hybrid microelectromechanical systems, or used as a functional filler in polymers. However, properties of talcas one of the main representatives of the phyllosilicate (sheet silicates) group are almost completely unexplored when ultrathin crystalline films and monolayers are considered. We investigate 2D talc flakes down to single layer thickness and reveal their efficiency for solid lubrication at the nanoscale. We demonstrate by atomic force microscopy based methods and contact angle measurements that several nanometer thick talc flakes have all properties necessary for efficient lubrication: a low adhesion, hydrophobic nature, and a low friction coefficient of 0.10 ± 0.02. Compared to the silicon-dioxide substrate, 2D talc flakes reduce friction by more than a factor of five, adhesion by around 20%, and energy dissipation by around 7%. Considering our findings, together with the natural abundance of talc, we put forward that 2D talc can be a cost-effective solid lubricant in micro- and nano-mechanical devices.

Viscoelastic properties are often measured using probe based techniques such as nanoindentation (NI) and atomic force microscopy (AFM). Rarely, however, are these methods verified. In this article, we present a method that combines contact mechanics with a viscoelastic model (VEM) composed of springs and dashpots. We further show how to use this model to determine viscoelastic properties from creep curves recorded by a probe based technique. We focus on using the standard linear solid model and the generalized Maxwell model of order 2. The method operates in the range of 0.01 Hz to 1 Hz. Our approach is suitable for rough surfaces by providing a defined contact area using plastic pre-deformation of the material. The very same procedure is used to evaluate AFM based measurements as well as NI measurements performed on polymer samples made from poly(methyl methacrylate) and polycarbonate. The results of these measurements are then compared to those obtained by tensile creep tests also performed on the same samples. It is found that the tensile test results differ considerably from the results obtained by AFM and NI methods. The similarity between the AFM results and NI results suggests that the proposed method is capable of yielding results comparable to NI but with the advantage of the imaging possibilities of AFM. Furthermore, all three methods allowed a clear distinction between PC and PMMA by means of their respective viscoelastic properties.

Changes in moisture content of single pulp fibers have an immense influence on the behavior of paper and paper products. Here, an atomic force microscopy (AFM)-based method is applied to investigate the viscoelastic properties of pulp fibers at varying relative humidity (RH) in the transverse direction. Pulp fibers have not only anisotropic properties, but also a very rough surface due to their hierarchical structure. For this reason, we have developed a specific load schedule for the AFM-based test method to overcome uncertainties and limitations due to surface roughness of the pulp fibers. The evaluation of the experimental data combines contact mechanics and viscoelastic models which consist of springs and dashpots in series or parallel describing elastic and viscous behavior. Here, it will be demonstrated that the so-called Generalized Maxwell (GM) model yields comparable results for single pulp fibers at five different RH values and in water. The moisture changes lead to a decrease in the elastic modulus but increase in the relaxation effects with increasing RH. All the determined parameters for the elastic and viscous behavior exhibit a gradual decrease with increasing RH from 10 to 75% RH. The elastic moduli decrease by a factor of 10 and the viscosities are decreasing by a factor of 10-20. In water, there is an even more pronounced decrease of the elastic moduli by a factor 100, and the viscosities decrease by at least three orders of magnitude compared to 10% RH. This indicates that the mechanical response of pulp fibers in water is significantly different than in humid air. This is also illustrated by the fact that a GM model of order two suffices to describe the material behavior in humid air but a GM model of order three is necessary to fit the material behavior in water. A possible interpretation is an additional relaxation effect of the pulp fiber wall in water.

Cellulose derivate phase separation in thin films was applied to generate patterned films with distinct surface morphology. Patterned polymer thin films are utilized in electronics, optics, and biotechnology but films based on bio-polymers are scarce. Film formation, roughness, wetting, and patterning are often investigated when it comes to characterization of the films. Frictional properties, on the other hand, have not been studied extensively. We extend the fundamental understanding of spin coated complex cellulose blend films via revealing their surface friction using Friction Force Microscopy (FFM). Two cellulose derivatives were transformed into two-phase blend films with one phase comprising trimethyl silyl cellulose (TMSC) regenerated to cellulose with hydroxyl groups exposed to the film surface. Adjusting the volume fraction of the spin coating solution resulted in variation of the surface fraction with the other, hydroxypropylcellulose stearate (HPCE) phase. The film morphology confirmed lateral and vertical separation and was translated into effective surface fraction. Phase separation as well as regeneration contributed to the surface morphology resulting in roughness variation of the blend films from 1.1 to 19.8 nm depending on the film composition. Friction analysis was successfully established, and then revealed that the friction coefficient of the films could be tuned and the blend films exhibited lowered friction force coefficient compared to the single-component films. Protein affinity of the films was investigated with bovine serum albumin (BSA) and depended mainly on the surface free energy (SFE) while no direct correlation with roughness or friction was found. BSA adsorption on film formed with 1:1 spinning solution volume ratio was an outlier and exhibited unexpected minimum in adsorption.

No abstract

No abstract

No abstract