Steel slag is a byproduct generated as waste during the steelmaking process and can be considered a cost-effective and environmentally acceptable alternative to replace natural aggregates. Using steel slag aggregates (SSA) to produce asphalt mixtures promotes sustainability and circular economy principles by using an industrial byproduct as a raw material. Thus, this work mainly aims to design more sustainable asphalt mixtures with high amounts of SSA that fit the circular economy expectations. This work developed two asphalt mixtures with SSA for surface (AC 14 surf) and binder/base (AC 20 bin/base) courses. Initially, the excellent wearing and polishing resistance of SSA and their good affinity with bitumen demonstrated the potential of this byproduct to be used in asphalt mixtures. Then, when analyzing the influence of using two different SSA incorporation rates (50% and a percentage close to 100%) in both asphalt mixtures, it was concluded that the use of SSA should be limited to 75% to avoid excessive air void contents and durability problems. The importance of considering the different particle densities of SSA and natural aggregates was highlighted during the mix design by defining a relationship between an effective and equivalent binder content. Finally, the mechanical performance of AC 14 and AC 20 with 75% SSA incorporation was compared to identical conventional mixtures produced with natural granite aggregates. The results obtained showed that the asphalt mixtures with 75% SSA have some workability problems due to the rough and porous surface of SSA. However, they present an excellent water sensitivity and permanent deformation resistance, surpassing the performance of the conventional asphalt mixtures.

Various researchers are developing efforts to integrate waste and by-products as alternative materials in road construction and maintenance, reducing environmental impacts and promoting a circular economy. Among the alternative materials that several authors have studied regarding their use as partial or total substitutes for natural aggregates in the asphalt paving industry, the steel slag aggregate (SSA) and recycled concrete aggregate (RCA) from construction demolition waste (CDW) stand out. This paper reviews and discusses the characteristics and performance of these materials when used as aggregates in asphalt mixtures. Based on the various studies analyzed, it was possible to conclude that incorporating SSA or RCA in asphalt mixtures for road pavements has functional, mechanical, and environmental advantages. However, it is essential to consider some possible drawbacks of these aggregates that are discussed in this paper, to define the acceptable uses of SSA and RCA as sustainable feedstocks for road paving works.

Road paving recycling has been acquiring more relevance in society, especially within the paradigm of a circular economy. The addition of waste materials in asphalt mixtures is an excellent solution to face the gradual emergence of a great diversity of waste materials and reduce the production costs. This study aims to evaluate the addition of commercial and laboratory-produced polymer modified binders as rejuvenators in recycled asphalt mixtures with high contents of reclaimed asphalt pavement material (RAP). A commercial polymer modified binder (PMB) and a conventional bitumen modified with 5% of styrene-butadiene-styrene (SBS) or 4% of Regefalt were added to RAP aged bitumen and compared with a rejuvenated binder. Fatigue, permanent deformation and water sensitivity tests carried out on recycled mixtures produced with those binders showed that polymer modified binders could be used as rejuvenators to improve their performance significantly. The recycled asphalt mixture produced with the commercial PMB presented the best mechanical performance. The polymer-modified binders revealed an ageing resistance equivalent to that of the control rejuvenated binder, or slightly better in the case of the final binder with SBS polymer.

Microsurfacing asphalt mixtures are a preventive maintenance technology comprising the application of a slurry (produced with a modified asphalt emulsion), aggregate, filler, and water on top of an existing pavement at ambient temperature. Although it is a widely used technology, further studies on the mix design procedures are necessary to ensure an adequate composition. Thus, this study contributes to developing an improved mix design procedure for microsurfacing asphalt mixtures. Different mixtures were prepared, and the influence of the type and amount of asphalt emulsion and the amount of added water and filler (cement) on the characteristics of the mixture were evaluated. Two preliminary tests, referred to as the “pizza test” and the “ball test”, were proposed to determine the initial proportions of added water and cement in the mixture, respectively. Then, consistency, cohesion, and shaking abrasion tests were performed to determine the optimum content of each component and evaluate their influence on the mixture characteristics. The results showed that these tests are essential to optimize the mix composition, even though it was found that the mix design of microsurfacings is a complex task because the mixture is a system with chemical interactions strongly influenced by its composition.