This paper introduces the concept of continuous chaotic printing, i.e. the use of chaotic flows for deterministic and continuous extrusion of fibers with internal multilayered micro- or nanostructures. Two free-flowing materials are coextruded through a printhead containing a miniaturized Kenics static mixer (KSM) composed of multiple helicoidal elements. This produces a fiber with a well-defined internal multilayer microarchitecture at high-throughput (>1.0 m min−1). The number of mixing elements and the printhead diameter determine the number and thickness of the internal lamellae, which are generated according to successive bifurcations that yield a vast amount of inter-material surface area (∼102 cm2 cm−3) at high resolution (∼10 µm). This creates structures with extremely high surface area to volume ratio (SAV). Comparison of experimental and computational results demonstrates that continuous chaotic 3D printing is a robust process with predictable output. In an exciting new development, we demonstrate a method for scaling down these microstructures by 3 orders of magnitude, to the nanoscale level (∼150 nm), by feeding the output of a continuous chaotic 3D printhead into an electrospinner. The simplicity and high resolution of continuous chaotic printing strongly supports its potential use in novel applications, including—but not limited to—bioprinting of multi-scale layered biological structures such as bacterial communities, living tissues composed of organized multiple mammalian cell types, and fabrication of smart multi-material and multilayered constructs for biomedical applications.

No abstract

No abstract

The biofabrication of living constructs containing hollow channels is critical for manufacturing thick tissues. However, current technologies are limited in their effectiveness in the fabrication of channels with diameters smaller than hundreds of micrometers. It is demonstrated that the co-extrusion of cell-laden hydrogels and sacrificial materials through printheads containing Kenics static mixing elements enables the continuous and one-step fabrication of thin hydrogel filaments (1 mm in diameter) containing dozens of hollow microchannels with widths as small as a single cell. Pre-vascularized skeletal muscle-like filaments are bioprinted by loading murine myoblasts (C2C12 cells) in gelatin methacryloyl -alginate hydrogels and using hydroxyethyl cellulose as a sacrificial material. Higher viability and metabolic activity are observed in filaments with hollow multi-channels than in solid constructs. The presence of hollow channels promotes the expression of Ki67 (a proliferation biomarker), mitigates the expression of hypoxia-inducible factor 1-alpha , and markedly enhances cell alignment (i.e., 82% of muscle myofibrils aligned (in ±10°) to the main direction of the microchannels after seven days of culture). The emergence of sarcomeric 𝜶-actin is verified through immunofluorescence and gene expression. Overall, this work presents an effective and practical tool for the fabrication of pre-vascularized engineered tissues.

We report a method for expanding microchannel-embedded paper devices using a precisely controlled gas-foaming technique for the generation of volumetric tissue models in vitro. We successfully fabricated hollow, perfusable microchannel patterns contained in a densely entangled network of bacterial cellulose nanofibrils using matrix-assisted sacrificial three-dimensional printing, and demonstrated the maintenance of their structural integrity after gas-foaming-enabled expansion in an aqueous solution of NaBH 4 . The resulting expanded microchannel-embedded paper devices showed multilayered laminar structures with controllable thicknesses as a function of both NaBH 4 concentration and expansion time. With expansion, the thickness and porosity of the bacterial cellulose network were significantly increased. As such, cellular infiltration was promoted comparing to as-prepared, non-expanded devices. This simple technique enables the generation of truly volumetric, cost-effective human-based tissue models, such as vascularized 8

This paper introduces the concept of continuous chaotic printing, i.e., the use of chaotic flows for deterministic and continuous fabrication of fibers with internal multilayered micro-or nanostructures. Two free-flowing materials are coextruded through a printhead containing a miniaturized Kenics static mixer (KSM) composed of multiple helicoidal elements. This produces a fiber with a well-defined internal multilayer microarchitecture at high speeds (>1.0 m min-1). The number of mixing elements and the printhead diameter determine the number and thickness of the internal lamellae, which are generated according to successive bifurcations that yield a vast amount of inter-material surface area (~102 cm2 cm-3) and high resolution features (~10 µm). In an exciting further development, we demonstrate a scale-down of the microstructure by 3 orders of magnitude, to the nanoscale level (~10 nm), by feeding the output of a continuous chaotic 3D printhead into an electrospinner. Comparison of experimental and computational results demonstrates the robust and predictable output and performance of continuous chaotic 3D printing. The simplicity and high resolution of continuous chaotic printing strongly supports its potential use in novel applications, including-but not limited to-bioprinting of multi-scale tissue-like structures, modeling of bacterial communities, and fabrication of smart multi-material and multilayered constructs.

No abstract

Multi-material and multilayered micro-and nanostructures are prominently featured in nature and engineering and are recognized by their remarkable properties. Unfortunately, the fabrication of micro-and nanostructured materials through conventional processes is challenging and costly. Herein, we introduce a high-throughput, continuous, and versatile strategy for the fabrication of polymer fibers with complex multilayered nanostructures. Chaotic electrospinning (ChE) is based on the coupling of continuous chaotic printing (CCP) and electrospinning, which produces fibers with an internal multi-material microstructure. When a CCP printhead is used as an electrospinning nozzle, the diameter of the fibers is further scaled down by 3 orders of magnitude while preserving their internal structure. ChE enables the use of various polymer inks for the creation of nanofibers with a customizable number of internal nanolayers. Our results showcase the versatility and tunability of ChE to fabricate multilayered structures at the nanoscale at high throughput. We apply ChE to the synthesis of unique carbon textile electrodes composed of nanofibers with striations carved into their surface at regular intervals. These striated carbon electrodes with high surface areas exhibit 3-to 4-fold increases in specific capacitance compared to regular carbon nanofibers; ChE holds great promise for the cost-effective fabrication of electrodes for supercapacitors and other applications.