Objective: To describe, using a three-dimensional finite element (FE) model, the initial force system generated during bodily movement of upper canines with plastic aligners with and without composite attachments. Materials and Methods: A CAD model of an upper right canine, its alveolar bone and periodontal ligament, thermoformed plastic aligner, and two light-cured composite attachments were constructed. A FE model was used to analyze the effects of imposing a distal movement condition of 0.15 mm on the aligner (simulating the mechanics used to produce a distal bodily movement) with and without composite attachments. Results: In terms of tension and compression stress distribution, without composite attachments a compression area in the cervical third of the distal root surface and a tension area in the apical third of the mesial surface were observed. With composite attachments, uniform compression areas in the distal root surface and uniform tension area in the mesial root surface were observed. Compression areas in the active surfaces of the composite attachments were also observed. In terms of movement patterns, an uncontrolled distal inclination, with rotation axis between the middle and cervical root thirds, was observed without composite attachment. Distal bodily movement (translation) was observed with composite attachment. Conclusions: In a three-dimensional FE analysis of a plastic aligner system biomechanically supplementary composite attachments generate the force system required to produce bodily tooth movement; the absence of biomechanically supplementary composite attachments favors the undesired inclination of the tooth during the translation movements. (Angle Orthod. 2015;85:454-460.)

This study exposes the assessment of a piezo-actuated sensor for monitoring elastic variations (change in Young’s modulus) of a host structure in which it is attached. The host structure is monitored through a coupling interface connected to the piezo-actuated device. Two coupling interfaces were considered (an aluminum cone and a human tooth) for the experimental tests. Three different materials (aluminum, bronze and steel) were prepared to emulate the elastic changes in the support, keeping the geometry as a fixed parameter. The piezo device was characterized from velocity frequency response functions in pursuance to understand how vibration modes stimulate the electrical resistance through electrical resonance peaks of the sensor. An impedance-based analysis (1–20 kHz) was performed to correlate elastic variations with indexes based on root mean square deviation (RMSD) for two observation windows (9.3 to 9.7 kHz and 11.1 to 11.5 kHz). Results show that imposed elastic variations were detected and quantified with the electrical resistance measurements. Moreover, it was demonstrated that the sensitivity of the device was influenced by the type of coupling interface since the cone was more sensitive than the tooth in both observation windows. As a final consideration, results suggest that bio-structures (fruits and bone, among others) could be studied since these can modify naturally its elastic properties.

No abstract

This study presents a numerical and experimental development of a piezo-actuated device used for monitoring the stiffness variations of its support through electromechanical impedance measurements. The piezo-device and its components define a clamped beam system activated dynamically by two piezo-transducers that transmit vibrations to the support (monitoring substrate). An harmonic finite element analysis was carried out to understand the effects of the substrate properties on the dynamics of the piezo-device. Experimental tests corroborated the simulations with the correspondence of modal shapes and frequency response functions (FRFs) when the substrate varies its stiffness. A biomedical application was conducted in a bone specimen with three embedded teeth to monitor the stiffness variations induced by drillings in the bone. Results showed that the bone stiffness monitoring could be possible through the teeth due to that the drillings effect were quantified by electrical impedance signals.

No abstract

No abstract

Bone tissue is a calcium deposit and supporting structure of the human body, it is exposed to several pathologies that modify its mineral content. To determine these changes, different diagnostic procedures are performed with techniques using invasive ionizing radiation, which are limited by the negative effects in the long term on human health. A methodology is explored that could be applicable in the diagnosis of pathologic variations in bone mineral density, using structural monitoring tools. The proposed technique estimates changes in bone conditions by applying impedance spectroscopy with a tooth-borne piezo-device. Bone-tooth samples were prepared to simulate a section of maxillary bone and subsequently treated with chemical agents, simulating pathologic decalcification. The piezo-device is inserted in the slot of an orthodontic bracket, previously bonded to the crown of the tooth, in order to transmit vibration to surrounding bone. The variations in bone micro-architecture were computed by image processing analyzed with samples prepared in transparent resin, allowing the measurement of morphometry before and after the induced changes in mineral content. Using vibrational bone response, impedance measurements allowed to observe the variations in bone mass as the samples were progressively decalcified. In the 5-50kHz spectrum, it was demonstrated the sensitivity of the electro-mechanical impedance during the bone alteration procedure since the electrical resistance signals of the piezo-device consistently changed in the frequency spectrum (5-50kHz). The piezo-device shows to be sensitive to the changes produced by the bone alterations, which were caused by the stiffness variations made in the sample during the decalcifying. These changes were statistically correlated to demonstrate that in a less invasive way, bone alterations could be monitored from the teeth. This result opens the door to search for a new way to diagnose bone density changes in real applications.

Colombian coffee production is well-known, and selective manual harvesting plays a vital task in guaranteeing high ripe coffee fruit rates in this process, leading to its known worldwide aroma and flavor. To maintain this quality approach, selective harvesting methods based on mechanical vibrations are a promising alternative for developing technologies that could accomplish the challenging Colombian coffee production context. In this study, a vibrations analysis in coffee fruits at three ripening stages was carried out to evaluate the dynamic behavior at two frequency windows: 10 to 100 Hz and 100 to 1000 Hz. Two groups of fruits previously classified in the CIELab color space were chosen for the vibration test study samples. Time and frequency signals were characterized via FFT (fast Fourier transform), and bump wavelets were determined to obtain the frequency–time magnitude scalograms. The measurements were obtained in three degrees of freedom over the fruits: one for measuring the input force (computed in voltage way) and the other two measured by the velocity. The results revealed frequency ranges with specific resonant peaks between 24 and 45 Hz, and close to 700 Hz, where the ripe fruits presented higher magnitudes in the calculated parameters. FFT of the velocity and scaled mechanical impedance were used to estimate these frequency ranges. This work is an important step to identify a “vibrational fingerprint” of each Coffea arabica var. Castillo fruit-ripening stage. However, we consider that more experiments should be performed to reconstruct the modal shape in each resonance. In future studies, fatigue analysis could show which are the most effective frequency ranges to detach the ripe fruits from the perspective of a real selective coffee-harvesting scenario.