Cardiotocography (CTG) lacks reliability and reproducibility and these problems are believed to be overcome by computer analysis. In this article we describe a system developed for routine clinical automated CTG analysis based on a low cost personal computer. Presently the system has processed 70 ten minute tracings. Fetal heart rate baseline, acceleration--deceleration detection, and long term variability estimation were performed in a satisfactory way.

The clinical demand for tissue-engineered bone is growing due to the increase of non-union fractures and delayed healing in an aging population. Herein, we present a method combining additive manufacturing (AM) techniques with cell-derived extracellular matrix (ECM) to generate structurally well-defined bioactive scaffolds for bone tissue engineering (BTE). In this work, highly porous three-dimensional polycaprolactone (PCL) scaffolds with desired size and architecture were fabricated by fused deposition modeling and subsequently decorated with human mesenchymal stem/stromal cell (MSC)-derived ECM produced in situ. The successful deposition of MSC-derived ECM onto PCL scaffolds (PCL-MSC ECM) was confirmed after decellularization using scanning electron microscopy, elemental analysis, and immunofluorescence. The presence of cell-derived ECM within the PCL scaffolds significantly enhanced MSC attachment and proliferation, with and without osteogenic supplementation. Additionally, under osteogenic induction, PCL-MSC ECM scaffolds promoted significantly higher calcium deposition and elevated relative expression of bone-specific genes, particularly the gene encoding osteopontin, when compared to pristine scaffolds. Overall, our results demonstrated the favorable effects of combining MSC-derived ECM and AM-based scaffolds on the osteogenic differentiation of MSC, resulting from a closer mimicry of the native bone niche. This strategy is highly promising for the development of novel personalized BTE approaches enabling the fabrication of patient defect-tailored scaffolds with enhanced biological performance and osteoinductive properties. † João C. Silva and Marta S. Carvalho contributed equally to this work.

Biomaterial properties and controlled architecture of scaffolds are essential features to provide an adequate biological and mechanical support for tissue regeneration, mimicking the ingrowth tissues. In this study, a bioextrusion system was used to produce 3D biodegradable scaffolds with controlled architecture, comprising three types of constructs: (i) poly(ε-caprolactone) (PCL) matrix as reference; (ii) PCL-based matrix reinforced with cellulose nanofibers (CNF); and (iii) PCL-based matrix reinforced with CNF and hydroxyapatite nanoparticles (HANP). The effect of the addition and/or combination of CNF and HANP into the polymeric matrix of PCL was investigated, with the effects of the biomaterial composition on the constructs (morphological, thermal, and mechanical performances) being analysed. Scaffolds were produced using a single lay-down pattern of 0/90°, with the same processing parameters among all constructs being assured. The performed morphological analyses showed a satisfactory distribution of CNF within the polymer matrix and high reliability was obtained among the produced scaffolds. Significant effects on surface wettability and thermal properties were observed, among scaffolds. Regarding the mechanical properties, higher scaffold stiffness in the reinforced scaffolds was obtained. Results from the cytotoxicity assay suggest that all the composite scaffolds presented good biocompatibility. The results of this first study on cellulose and hydroxyapatite reinforced constructs with controlled architecture clearly demonstrate the potential of these 3D composite constructs for cell cultivation with enhanced mechanical properties.

Recent classifications proved to be more accurate in predicting important clinical outcomes in patients with AP.

Considering the expected increasing demand for cellulose fibers in the near future and that its major source is wood pulp, alternative sources such as vegetable wastes from agricultural activities and agro-food industries are currently being sought to prevent deforestation. In the present study, cellulose was successfully isolated from six agroindustrial residues: corncob, corn husk, grape stalk, pomegranate peel, marc of strawberry-tree fruit and fava pod. Cellulose fibers were characterized by Fourier-transform infrared spectroscopy, thermogravimetric analysis, stereomicroscopy and scanning electron microscopy (SEM). Despite the evident morphological differences among the extracted celluloses, results revealed similar compositional and thermal properties with the wood-derived commercial microcrystalline cellulose used as a control. Trace amounts of lignin or hemicellulose were detected in all cellulose samples, with the exception of corncob cellulose, that exhibited the greatest extraction yield (26%) and morphological similarities to wood-derived microcrystalline cellulose, visible through SEM. Furthermore, corncob cellulose was found to have thermal properties (TOnset of 307.17 °C, TD of 330.31 °C, and ΔH of 306.04 kJ/kg) suitable for biomedical applications.

No abstract

No abstract

Temporomandibular disorders (TMD) affect a substantial percentage of the population, and the resources spent on their treatment are considerable. Despite the worldwide efforts around Tissue Engineering of the temporomandibular joint (TMJ) disc, a proper implant offering a long-term solution for TMD was not yet developed. To contribute to these efforts, this work is focused on the research and development of implants for TMJ disc regeneration. Scaffolds and hydrogels mimicking the TMJ disc of black Merino sheep were produced using different materials, poly(ε-caprolactone) (PCL) and poly(ethylene glycol) diacrylate (PEGDA), and as a multi-material structure. Different parameters of the scaffold manufacturing were assessed: the influence of processing temperatures, filament diameter, and biological environment. Moreover, two multimaterial approaches were also assessed, scaffold with a hydrogel shell and scaffold with a hydrogel core. It was found that increasing temperature, the scaffolds' porosity decreases, increasing their compressive modulus. Decreasing the filament size (300 to 200 µm) decreases the compressive modulus to almost half of the initial value. Scaffolds with 200 µm filaments are the ones with a closer modulus to the native disc and their properties are maintained under hydrated conditions. The introduction of a hydrogel core in these scaffolds presented better mechanical properties to TMJ disc substitution.