CuInSe2 (CISe) quantum dots (QDs) were synthesized with tunable size from less than 2 to 7 nm diameter. Nanocrystals were made using a secondary phosphine selenide as the Se source, which, compared to tertiary phosphine selenide precursors, was found to provide higher product yields and smaller nanocrystals that elicit quantum confinement with a size-dependent optical gap. Photovoltaic devices fabricated from spray-cast CISe QD films exhibited large, size-dependent, open-circuit voltages, up to 849 mV for absorber films with a 1.46 eV optical gap, suggesting that midgap trapping does not dominate the performance of these CISe QD solar cells.

Pyrite-phase iron sulfide (FeS2) nanocrystals were synthesized to form solvent-based dispersions, or "solar paint," to fabricate photovoltaic devices (PVs). Nanocrystals were sprayed onto substrates as absorber layers in devices with several different architectures, including Schottky barrier, heterojunction, and organic/inorganic hybrid architectures, to explore their viability as a PV material. None of the devices exhibited PV response. XRD and Raman spectroscopy confirmed the pyrite composition and phase purity of the nanocrystals. The electrical conductivity of the nanocrystal films was about 4 to 5 S/cm, more typical of metal nanocrystal films than semiconductor nanocrystal films, and the lack of PV response appears to derive from the highly conductive surface-related defects in pyrite that have been proposed.

No abstract

Thin film photovoltaic devices (PVs) were fabricated with CuInSe(2) (CIS) nanocrystals capped with either oleylamine, inorganic metal chalcogenide-hydrazinium complexes (MCC), or S(2-), HS(-), and OH(-). A CIS nanocrystal layer deposited from solvent-based inks without high temperature processing served as the active light-absorbing material in the devices. The MCC ligand-capped CIS nanocrystal PVs exhibited power conversion efficiency under AM1.5 illumination (1.7%) comparable to the oleylamine-capped CIS nanocrystals (1.6%), but with significantly thinner absorber layers. S(2-)-capped CIS nanocrystals could be deposited from aqueous dispersions, but exhibited lower photovoltaic performance.

Peak external quantum efficiencies (EQEs) of just over 120% were observed in photovoltaic (PV) devices of CuInSe2 nanocrystals prepared with a photonic curing process. The extraction of more than one electron/hole pair as a result of the absorption of a single photon can occur if multiple excitons are generated and extracted. Multiexciton generation (MEG) in the nanocrystal films was substantiated by transient absorption spectroscopy. We propose that photonic curing leads to sufficient electronic coupling between nanocrystals to enable multiexciton extraction under typical solar illumination conditions. Under low light conditions, however, the EQE drops significantly, indicating that photonic curing-induced ligand desorption creates a significant amount of traps in the film that limit the overall power conversion efficiency of the device.

No abstract

The power conversion efficiency of photovoltaic devices made with ink-deposited Cu(InxGa1-x)Se2 (CIGS) nanocrystal layers can be enhanced by sintering the nanocrystals with a high temperature selenization process. This process, however, can be challenging to control. Here, we report that ink deposition followed by annealing under inert gas and then selenization can provide better control over CIGS nanocrystal sintering and yield generally improved device efficiency. Annealing under argon at 525 °C removes organic ligands and diffuses sodium from the underlying soda lime glass into the Mo back contact to improve the rate and quality of nanocrystal sintering during selenization at 500 °C. Shorter selenization time alleviates excessive MoSe2 formation at the Mo back contact that leads to film delamination, which in turn enables multiple cycles of nanocrystal deposition and selenization to create thicker, more uniform absorber films. Devices with power conversion efficiency greater than 7% are fabricated using the multiple step nanocrystal deposition and sintering process.

Transient absorption spectroscopy (TAS) was used to study carrier multiplication (CM) (also called multiexciton generation (MEG)) in solvent-dispersed colloidal CuInSe2 nanocrystals with diameters as small as 4.5 nm. Size-dependent carrier cooling rates, absorption cross sections, and Auger lifetimes were also determined. The energy threshold for CM in the CuInSe2 nanocrystals was found to be 2.4 ± 0.2 times the nanocrystal energy gap (Eg) and the CM efficiency was 36 ± 6% per unit Eg. This is similar to other types of nanocrystal quantum dot materials.