Electron heating and the energy inventory during asymmetric reconnection are studied in the laboratory plasma with a density ratio of about 8 across the current sheet. Features of asymmetric reconnection such as the large density gradients near the low‐density side separatrices, asymmetric in‐plane electric field, and bipolar out‐of‐plane magnetic field are observed. Unlike the symmetric case, electrons are also heated near the low‐density side separatrices. The measured parallel electric field may explain the observed electron heating. Although large fluctuations driven by lower hybrid drift instabilities are also observed near the low‐density side separatrices, laboratory measurements and numerical simulations reported here suggest that they do not play a major role in electron energization. The average electron temperature increase in the exhaust region is proportional to the incoming magnetic energy per an electron/ion pair but exceeds scalings of the previous space observations. This discrepancy is explained by differences in the boundary condition and system size. The profile of electron energy gain from the electric field shows that there is additional electron energy gain associated with the electron diamagnetic current besides a large energy gain near the X line. This additional energy gain increases electron enthalpy, not the electron temperature. Finally, a quantitative analysis of the energy inventory during asymmetric reconnection is conducted. Unlike the symmetric case where the ion energy gain is about twice more than the electron energy gain, electrons and ions obtain a similar amount of energy during asymmetric reconnection.

The physical properties of a wave transmission spectrum were analyzed using a wave-cutoff probe and a three-dimensional wave simulation in weakly ionized plasma. The experimental wave transmission was compared to the calculated wave transmission. The new path of wave transmission below the wave-cutoff frequency was found, and the wave transmission properties depending on the chamber geometry above the wave-cutoff frequency were also analyzed. Through these wave transmission results, the causes of an electromagnetic propagation phenomenon below the wave-cutoff frequency were examined. Moreover, the impacts of a cavity mode within the plasma chamber on the features of wave transmission were identified.

The wave cutoff probe, a precise measurement method for measuring the electron density, was recently proposed. To characterize the cutoff probe system, in this paper, the microwave simulations of a cutoff probe system were performed at various configurations of the cutoff probe system. The influence of the cutoff probe spectrum stemming from numerous parametric elements such as the probe tip length, probe tip distance, probe tip plane orientation, chamber volume/geometry, and coaxial cable length is presented and discussed. This article is expected to provide qualitative and quantitative insight into cutoff probe systems and its optimization process. V C 2012 American Institute of Physics. [http://dx.

We use a newly developed simulation tool to numerically study fast-ion loading on plasma-facing components (PFCs) at the Korea Superconducting Tokamak Advanced Research facility in the high-poloidal-β plasma operation regime. The new code can calculate neutral beam ionization and follow the guiding center orbit of ionized particles. The results of the simulation indicate that fast ions ionized in the high-field side drift out and strike the PFCs as they rotate poloidally. Momentum projection onto a phase space defined by canonical toroidal angular momentum and magnetic moment leads to a simple criterion to avoid fast-ion loading on poloidal limiters (PLs), which are PFCs that are toroidally localized on the low-field side. Control of fast-ion loss is examined by varying the plasma current and plasma boundary. A larger plasma current and inner shifting of the outer plasma boundary is predicted to substantially reduce fast-ion loading on the PLs. The proposed phase-space criterion is qualitatively consistent with the results of the simulation of fast-ion control.

No abstract

This paper proposes a new method for cutoff probe using a nanosecond impulse generator and an oscilloscope, instead of a network analyzer. The nanosecond impulse generator supplies a radiating signal of broadband frequency spectrum simultaneously without frequency sweeping, while frequency sweeping method is used by a network analyzer in a previous method. The transmission spectrum (S21) was obtained through a Fourier analysis of the transmitted impulse signal detected by the oscilloscope and was used to measure the electron density. The results showed that the transmission frequency spectrum and the electron density obtained with a new method are very close to those obtained with a previous method using a network analyzer. And also, only 15 ns long signal was necessary for spectrum reconstruction. These results were also compared to the Langmuir probe's measurements with satisfactory results. This method is expected to provide not only fast measurement of absolute electron density, but also function in other diagnostic situations where a network analyzer would be used (a hairpin probe and an impedance probe) by replacing the network analyzer with a nanosecond impulse generator and an oscilloscope.

Pressure limitation of electron density measurement is presented using a wave-cutoff method. As gas pressure builds up, the electron motion at ω=ωp is disturbed by an electron-neutral collision and cannot catch up to the movement of the electromagnetic wave. For this reason, electromagnetic waves begin to penetrate into plasma and the wave-cutoff signal disappears as the gas pressure increases. This was also confirmed by using an impedance analysis of the probe system. The results corresponded well with the measured wave transmission characteristics at the plasma frequency.

Self-oscillation obtained using a DC-only power supply under specific anode voltage conditions is investigated in a cylindrical system with thermal electrons using tungsten filaments. Analysis of the obtained oscillation profiles reveals that the experimental data are consistent with a model derived from the particle balance model. The self-oscillation period characteristics with respect to the pressure and gas species are also analyzed. As the physics and particle motion of self-oscillation near the plasma transition region are analyzed from different perspectives, this paper may advance the study of this phenomenon.