This cross-sectional observational study with 24 patients evaluated differences in bite force (BF) and masticatory performance (MP) between conventional complete denture (CCD) and implant mandibular overdenture (IMO) users and the correlation between these variables. The BF test was performed bilaterally with an occlusal force device. During the MP test, patients were asked to chew Optocal particles for 40 cycles. The Shapiro Wilk test was employed to verify the normality of the data, the student t test to identify differences between groups, and Pearson’s correlation to investigate interrelationships between variables. A multiple linear regression was subsequently performed via the stepwise method. P values ≤0.05 were considered statistically significant. Unlike IMO users, CCD users presented a significant difference (25.6%) in BF between the dominant and non-dominant chewing side (p=0.04). IMO users presented significantly higher BF (p=0.01) without presenting a dominant side (p=0.38), and also performed significantly better for the following MP parameters: MPX50 values decreased by 27.25% in IMO users (p=0.01), MPB decreased by 48.38% (p=0.01), and ME 5.6 decreased by 53.25% (p=0.02), while ME2.8 increased by 151.57% (p=0.01). The BF and MPX50 in the IMO wearers group were negatively correlated (-0.57; p=0.05); this correlation coefficient was the only parameter included in the multivariate regression model. IMO users have higher BF and better masticatory performance than CCD users, especially in terms of chewed particles size reduction. MP is correlated with a higher BF in IMO users through better particle trituration.
This study investigated the presence of co-authorship from Brazil in articles published in top-tier dental journals and analyzed the influence of international collaboration, article type (original research or review), and funding on citation rates. Articles published between 2015 and 2017 in 38 selected journals from 14 dental subareas were screened in Scopus. Bibliographic information, citation counts, and funding details were recorded for all articles (N=15619). Collaboration with other top-10 publishing countries in dentistry was registered. Annual citations averages (ACA) were calculated. A linear regression model assessed differences in ACA between subareas. Multilevel linear regression models evaluated the influence of article type, funding, and presence of international collaboration in ACA. Brazil was a frequent co-author of articles published in the period (top 3: USA=25.5%; Brazil=13.8%; Germany=9.2%) and the country with most publications in two subareas. The subjects with the biggest share of Brazil are Operative Dentistry/Cariology, Dental Materials, and Endodontics. Brazil was second in total citations, but fifth in citation averages per article. From the total of 2155 articles co-authored by Brazil, 74.8% had no co-authorship from other top-10 publishing countries. USA (17.8%), Italy (4.2%), and UK (3.2%) were the main co-author countries, but the main collaboration country varied between subjects. Implantology and Dental Materials were the subjects with most international co-authorship. Review articles and articles with international collaboration were associated with increased citation rates, whereas the presence of study funding did not influence the citations.
This study investigated the effect of ultrasound application when luting ceramic using two preheated composites that show distinct responses to preheating at 69°C: Filtek Z100 and Z350XT. RelyX Veneer was the control. Feldspar disks were luted using the resinbased luting agents (RBLAs), and ultrasound was tested. Biaxial flexure strength (σbf) was calculated at z-axial positions of the luted disks (z=0; z=−t2). Microtensile bond strength (μTBS) to ceramic was tested (n=30). Data were analyzed at α=0.05. At z=0, the σbf was higher for Z350 when ultrasound was not used. When ultrasound was applied, the σbf was similar between Z350 and Z100. At z=−t2, differences across the RBLAs were observed: Z350 was superior than Z100 and control without ultrasound. Ultrasound increased σbf for Z100 at both axial positions. The preheated composites yielded higher μTBS than the control. Ultrasonication increased the mechanical performance of ceramic luted with Z100 without influencing the film thickness.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.