No abstract

No abstract

No abstract

The long-term survival of cemented hip replacements depends on the ability of the cemented fixation to resist fatigue damage. Damage has been assumed to accumulate linearly (Miner's law) even though it is unlikely to be the case in such a porous brittle material. This study addresses the nonlinear stress-dependent nature of fatigue damage accumulation in acrylic bone cement. Specimens were subjected to a zero-to-tension fatigue load in water at 37 degrees C. A total of 15 specimens were tested, i.e., five specimens at each of three stress levels. The specimens were cyclically loaded to a certain fraction of their fatigue lives and the amount of microcracking present at that time was quantified by counting each crack and measuring its length. This procedure was repeated until the specimen failed. A total of 801 cracks formed in the 15 specimens. All cracks were found to initiate at pores. Crack propagation directions were distributed normally about the direction perpendicular to the applied load at the lower stress levels, but at higher stress, the distribution tended to be broader. At higher stresses, more cracks were produced per pore. The damage accumulation process in acrylic bone cement was found to be nonlinear with the degree of nonlinearity increasing with stress. Furthermore, great variability was found which was attributed to the differences in porosity between specimens. A power law equation is given which describes the predicted relationship between damage accumulation and number of loading cycles as a function of the stress level.

Coronary stents are used to re-establish the vascular lumen and flow conditions within the coronary arteries; the typical thickness of a stent strut is 100 microm, and average grain sizes of approximately 25 microm exist in stainless steel stents. The purpose of this study is to investigate the effect of strut size on the stress strain behavior of 316 L stainless steel. Other materials have shown a size dependence at the micron size scale; however, at present there are no studies that show a material property size dependence in coronary stents. Electropolished stainless steel stent struts within the size range of 60-500 microm were tensile tested. The results showed that within the size range of coronary stent struts a size dependent stress-strain relationship is required to describe the material. Finite element models of the final phase of fracture, i.e., void growth models, explained partially the reason for this size effect. This study demonstrated that a size based stress-strain relationship must be used to describe the tensile behavior material of 316 L stainless steel at the size scale of coronary stent struts.

Heart failure is a significant clinical issue. It is the cause of enormous healthcare costs worldwide and results in significant morbidity and mortality. Cardiac regenerative therapy has progressed considerably from clinical and preclinical studies delivering simple suspensions of cells, macromolecule, and small molecules to more advanced delivery methods utilizing biomaterial scaffolds as depots for localized targeted delivery to the damaged and ischemic myocardium. Here, regenerative strategies for cardiac tissue engineering with a focus on advanced delivery strategies and the use of multimodal therapeutic strategies are reviewed.

The durability of bovine pericardium leaflets employed in bioprosthetic heart valves (BHVs) can significantly limit the longevity of heart valve prostheses. Collagen fibres are the dominant load bearing component of bovine pericardium, however fibre architecture within leaflet geometries is not explicitly controlled in the manufacture of commercial devices. Thus, the purpose of this study was to ascertain the influence of pre-determined collagen fibre orientation and dispersion on the mechanical performance of bovine pericardium. Three tissue groups were tested in uniaxial tension: cross-fibre tissue (XD); highly dispersed fibre-orientations (HD); or preferred-fibre tissue (PD). Both the XD and PD tissue were tested under cyclic loading at 1.5 Hz and a stress range of 2.7 MPa. The results of the static tensile experiments illustrated that collagen fibre orientation and degree of alignment significantly influenced the material's response. Whereby, there was a statistically significant decrease in material properties between the XD groups and both the PD and HD groups for ultimate tensile strength and stiffness (p<0.01). Furthermore, HD tissue had a stiffness of approximately 58% of the PD group, and XD tissue had a stiffness of approximately 18% of the PD group. The dynamic behaviour of the XD and PD groups was extremely distinct; for example a Weibull analysis indicated that the 50% probability of failure in specimens with fibres orientated perpendicular (XD) to the loading direction occurred at 375 cycles. Due to this failure, XD specimens survived less than 20% of the cycles completed by those in which fibres were aligned along the loading direction (PD). The results from this study indicate that fibre architecture is a significant factor in determining static strength and fatigue life in bovine pericardium, and thus must be incorporated in the design process to improve future device durability.

No abstract