In recent decades, three-dimensional (3D) printing as an emerging technology, has been utilized for imparting human anatomy knowledge. However, most 3D printed models are rigid anatomical replicas that are unable to represent dynamic spatial relationships between different anatomical structures. In this study, the data obtained from a computed tomography (CT) scan of a normal knee joint were used to design and fabricate a functional knee joint simulator for anatomical education. Utility of the 3D printed simulator was evaluated in comparison with traditional didactic learning in first-year medical students (n = 35), so as to understand how the functional 3D simulator could assist in their learning of human anatomy. The outcome measure was a quiz comprising 11 multiple choice questions based on locking and unlocking of the knee joint. Students in the simulation group (mean score = 85.03%, ±SD 10.13%) performed significantly better than those in the didactic learning group, P < 0.05 (mean score = 70.71%, ±SD 15.13%), which was substantiated by large effect size, as shown by a Cohen's d value of 1.14. In terms of learning outcome, female students who used 3D printed simulators as learning aids achieved greater improvement in their quiz scores as compared to male students in the same group. However, after correcting for the modality of instruction, the sex of the students did not have a significant influence on the learning outcome. This randomized study has demonstrated that the 3D printed simulator is beneficial for anatomical education and can help in enriching students' learning experience. Anat Sci Educ 12: 610-618.
Objectives: Extraction of impacted mandibular third molars is one of the most common surgical procedures performed at dental clinics; however effective training models for teaching oral surgery to dental students are limited. This study aimed to use three-dimension (3D) printing technology to develop an effective training model for impacted third molar extraction. Methods: The data for the 3D model were digitally processed using highresolution computed tomography, and two common, but different patterns of impacted third molars were simulated using computer-aided design. Thereafter, the model was printed using the 3D-printing technology, and the efficiency of the 3D-printed model and an animal model (pig mandible) were compared using a five-point Likert scale by 35 oral surgeons in the oral surgery department and 208 students of stomatology in the internship stage. Results:The 3D-printed model consisted of three parts: a non-replaceable part (i.e., the body of the mandible and the teeth from the left first molar to the right first molar) and two replaceable parts (i.e., the part of the ascending ramus of the mandible, as well as the second and third molars). It was covered with a layer of rubber-like material to simulate the gingiva. For the comparison between the 3D-printed and animal models, a total of 205 questionnaires were collected. Both oral surgeons and students agreed that the 3D-printed model was better than the animal model in terms of total value and the anatomy of the bone and teeth, simulating the surgical procedure (p < 0.05), while the two models achieved similar results for haptic feedback of the soft tissue (p > 0.05). Conclusions:The 3D-printed model is realistic and effective for learning impacted third molar extraction and received positive feedback from students and oral surgeons. This model can significantly improve the pre-clinical skill training of dental students.
The advent of new technologies in medical imaging and 3D printing in recent years has made customization of surgical tools and implants more accessible, revolutionizing many surgical fields. In many human diseases, these implants have led to superior surgical outcomes and greatly improved patients’ quality of life. Thus, it is of great interest to apply these technologies to the treatment of animal diseases. In this study, we report the use of computed tomography (CT) and 3D printing for the treatment of a Great Hornbill at Jurong Bird Park that was diagnosed with squamous cell carcinoma of the casque. A 3D printed prosthesis that perfectly fitted the subject was implanted to replace its resected casque. The subject exhibited natural eating behaviour with no post-operative complications. Using this case as an example, the positive outcomes suggest a great potential in applying these technologies to the treatment of other wildlife diseases.
Purpose The aims of this study were (1) to develop a three-dimensional (3D) printed simulator that facilitates the simulation of surgical skills for portal placement, intra-articular identification of anatomical structures and arthroscope navigation for hip arthroscopy and (2) to concurrently examine the feasibility of using this simulator as an assessment tool to evaluate trainees’ surgical competencies. Methods A simulator was developed using a combination of medical imaging, computer-aided design, and 3D printing. A cross-sectional study was conducted with 29 participants divided into 3 subgroups (novice, intermediate and experienced). All participants performed related skills on the simulator, and their performance was evaluated using different assessment parameters. The participants’ qualitative feedback regarding the simulator was also collected. The data collated from each group of participants were subsequently compared. Results Significant differences were observed between the three subgroups of participants with regard to the total checklist score (F2,26 = 11.3), total Arthroscopic Surgical Skill Evaluation score (F2,26 = 92.1), overall final global rating scale score (F2,26 = 49), number of times the participants used fluoroscopy (F2,26 = 7.4), and task completion times (F2,26 = 23.5). The participants’ performance in the simulated operation was correlated with their prior clinical experience. There was mainly positive feedback with regard to the fidelity and utility of the simulator in relation to the surgeons’ prior clinical experience. Conclusions This study demonstrated that a reliable hip arthroscopic simulator can be developed for use by orthopedic surgeons to evaluate their hip arthroscopic skills before performing actual surgical operations. Level of evidence Level III.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.