The Barrett Universal II, Haigis, Hoffer Q, Holladay 2, RBF method and SRK/T formulas were equally accurate in predicting the IOL power in eyes shorter than 22.0 mm.

PurposeThis study aimed to evaluate whether different anterior chamber depth (ACD) affects the predictive accuracy of intraocular lens formulas in eyes with axial length (AL) less than 22 mm.MethodsEighty-five eyes of 85 patients with AL less than 22 mm were included in this retrospective study, which were divided into three groups: Group 1, ACD less than 2.4 mm; Group 2, ACD between 2.4 and 2.9 mm; and Group 3, ACD greater than 2.9 mm. Optical biometry with partial coherence interferometry was performed in all cases. The median absolute error (MedAE) was compared by Friedman’s test, using the optimized lens constant, among seven formulas (Barrett Universal II, Haigis, Hill-RBF, Hoffer Q, Holladay 1, Holladay 2, and SRK/T) in each group.ResultsFriedman’s test showed no significant difference in MedAE among all formulas in Groups 1 and 3. However, as the Haigis formula had the highest MedAE and lowest percentage of eyes within ±0.25 Diopter, it is least preferred in Group 1. On the contrary, in Group 3 it fared the best, having the least MedAE and highest percentage of eyes within ±0.25 Diopter. In Group 2, Friedman’s test gave significant difference, and post-hoc analysis showed statistical superiority of Haigis over the Holladay 1 (p=0.02), Holladay 2 (p=0.01), Hill-RBF (p=0.04), and SRK/T (p=0.02) formulas. However, there was no statistical difference between the Barrett Universal II, Haigis, and Hoffer Q formulas.ConclusionConsidering the ACD in eyes with AL less than 22 mm, Haigis is the preferred formula while SRK/T proved to be the worst formula in Groups 2 and 3.

No abstract

Purpose – The purpose of this paper is to study and calculate the electrical characteristic of an equilateral triangular microstrip patch antenna that is proposed for dual frequency operation using the pin diode. The electrical characteristic of an equilateral triangular microstrip patch antenna is proposed for dual-frequency operation. Spur lines and ON/OFF condition of the pin diode are utilized to switch the resonant frequency of the patch. The presence of spur lines excites the surface current of the patch which is dependent on the resonant frequency of an equilateral triangular microstrip patch. Insertion of the diode in the spur lines gives a better result and compactness in patch design, which improves the miniaturization in size of patch. Design/methodology/approach – Antenna Design Aspects: A basic structure of an equilateral triangular microstrip antenna (ETMA) having two spur lines and one pin diode positioned in between the spur line is considered in this paper. The design parameters are chosen on the basis of substrate materials having relative permittivity less than three. Specification of the antenna is given in Table I. Substrate material used is RT Duroid 5,880; relative permittivity of the substrate er is 2.2; thickness of dielectric substrate h is 1.5 mm; sides of equilateral triangular patch a are 10 mm, spur width s is 0.5 mm; and spur length b is 2.0 mm. Findings – This paper gives an account of achieving polarization swiftness with coplanar waveguide (CPW) feed. The miniaturized size of the antenna is 35 × 30 mm2. Switchable microstrip equilateral triangular antenna has been demonstrated for dual-frequency operations. The resonant frequency of an ETMA can be adjusted by setting the diode in an ON and OFF state. The design improves the miniaturization in size with a discussion of radiation density. The excited patch surface current is limited to flow around just the mid of the patch in simple ETMA with a single slit cut. It is observed that for an ETMA, when the diode is in the ON state at 9.16 GHz, the excited patch surface current is highly distributed in the patch compared to when the diode is in the ON state at 11 GHz. Similarly, it is observed that the excited surface patch current is highly distributed when the diode is in the OFF state in both frequencies (9 and 11.96 GHz). The mode is changed by the use of a switch at time and it is suitable for wireless communication applications. Originality/value – Spur lines and the ON/OFF condition of the pin diode are utilized to switch the resonant frequency of the patch. The presence of spur lines excites the surface current of the patch which is dependent on the resonant frequency of an equilateral triangular microstrip patch. Insertion of the diode in spur lines gives a better result and compactness in patch design, which improves the miniaturization in size of the patch.

No abstract

No abstract

In this paper, a new design of dual slit equilateral triangular shaped microstrip antenna approach is proposed with compactness in patch size of antenna. Dual slit cut equilateral triangular microstrip patch antenna is designed on a substrate which provides wideband characteristics compared to without slit and single slit cut equilateral triangular shaped microstrip antenna. The method of moments based HFSS software has been used for generation and analysis of dual slit cut microstrip antenna. Theoretical and simulated results are presented and compared.

In this paper, a novel structure of slit-cut stacked equilateral triangular microstrip antenna (ETMA) has been theoretically studied using cavity model and found in agreement with the stimulated result calculated by high frequency simulator structure (HFSS). The analysis of stacked ETMA and slit-cut ETMA is done. The theoretical and simulated results of stacked ETMA and slit-cut ETMA are presented and compared. The main concentration is to find the different results, i.e. input impedance and return loss of the slit-cut ETMA and slit-cut stacked ETMA.