We report the high capacity and rate capability of mesoporous Co3O4 nanowire (NW) arrays as anodes in Li ion batteries. At a current of 1C, the NW arrays maintain a capacity of 700 mAh/g after 20 discharge/charge cycles. When the current is increased to 50C, 50% of the capacity can be retained. With their ease of large area synthesis and superior electrochemical properties, these Co3O4 NW arrays will be interesting for practical Li ion batteries.

Dye-sensitized solar cells were fabricated based on the composites of anatase TiO2 nanoparticles and single crystalline anatase TiO2 nanowires. Nanoparticle/nanowire composites can possess the advantages of both building blocks, i.e., the high surface area of nanoparticle aggregates and the rapid electron transport rate and the light scattering effect of single-crystalline nanowires. Three different composites were prepared with 5 wt %, 20 wt %, and 77 wt % nanowires, respectively. The performances of composite solar cells were compared with pure nanoparticle cells at a series of film thickness. With low nanowire concentrations (5 wt % and 20 wt %), the composite films maintain similar specific surface area as the pure nanoparticle films, while the composite cells show higher short-circuit current density and open-circuit voltage. An enhancement of power efficiency from 6.7% for pure nanoparticle cells to 8.6% for the composite cell with 20 wt % nanowires has been achieved under 1 Sun AM1.5 illumination (100 mW/cm2). For the composite film with 77 wt % nanowires, the nanowires became the major phase. Their less compact packing resulted in significant decrease of the specific surface area, and thus the current density. However, with the increase of film thickness, the current density showed a continuous increase in the whole thickness range up to 17 microm, indicating the improved electron diffusion length due to the formed nanowire network. The nanowires also helped to preserve crack-free thick films. These results show that employing nanoparticle/nanowire composites represents a promising approach for further improving the efficiencies of sensitized solar cells.

Developing new electrode materials is important for high-performance dye-sensitized solar cells (DSSCs). Previous research has mostly been limited to simple binary oxides. The application of multication oxides in DSSC has been rarely explored. In this communication, we report the promising application of Zn2SnO4 nanoparticles in DSSC. An overall light-to-electricity efficiency as high as 3.8% has been achieved under 1 sun AM 1.5 illumination. In comparison with ZnO and SnO2 as its simple component oxides, a Zn2SnO4 cell is more stable against acidic dyes than a ZnO cell, while it has much better performance than a SnO2 cell. Our results suggest that multication oxides, with the availability of a wide range of compositions and tunable properties, hold great promise as new electrode materials for DSSCs.

We report a facile template-free method for the large-area growth of freestanding hollow Co3O4 nanowire arrays on a variety of substrates including transparent conducting glass, Si wafer, and copper foil, et al. These nanowires have the interesting combined properties of mesoporosity and quasi-single-crystallinity. With their high surface area and crystallinity, and their direct growth on conductive substrate, these Co3O4 nanowire arrays will have promising applications in lithium-ion batteries, chemical sensing, and field-emission and electrochromic devices. Using the prepared nanowire arrays as electrode, an electrochemical sensor for hydrogen peroxide sensing has been demonstrated.

Hollow spherical silica particles with hexagonally ordered mesoporous shells are synthesized with the dual use of cetyltrimethylammonium bromide (CTAB) and unmodified polystyrene latex microspheres as templates in concentrated aqueous ammonia. In most of the hollow mesoporous particles, cylindrical pores run parallel to the hollow core due to interactions of CTAB/silica aggregates with the latices. Effects on the product structure of the CTAB:latex ratio, the amount of aqueous ammonia, and the latex size are studied. Hollow particles with hexagonally patterned mesoporous shells are obtained at moderate CTAB:latex ratios. Too little CTAB causes silica shell growth without surfactant templating, and too much induces nucleation of new mesoporous silica particles without latex cores. The concentration of ammonia must be large to induce co-assembly of CTAB, silica, and latex into dispersed particles. The results are consistent with the formation of particles by addition of CTAB/silica aggregates to the surface of latex microspheres. When the size and number density of the latex microspheres are changed, the size of the hollow core and the shell thickness can be controlled. However, if the microspheres are too small (50 nm in this case), agglomerated particles with many hollow voids are obtained, most likely due to colloidal instability.