Non-aqueous metal-oxygen batteries depend critically on the reversible formation/decomposition of metal oxides on cycling. Irreversible parasitic reactions cause poor rechargeability, efficiency, and cycle life and have predominantly been ascribed to the reactivity of reduced oxygen species with cell components. These species, however, cannot fully explain the side reactions. Here we show that singlet oxygen forms at the cathode of a lithium-oxygen cell during discharge and from the onset of charge, and accounts for the majority of parasitic reaction products. The amount increases during discharge, early stages of charge, and charging at higher voltages, and is enhanced by the presence of trace water. Superoxide and peroxide appear to be involved in singlet oxygen generation. Singlet oxygen traps and quenchers can reduce parasitic reactions effectively. Awareness of the highly reactive singlet oxygen in non-aqueous metal-oxygen batteries gives a rationale for future research towards achieving highly reversible cell operation.

Aprotic sodium–O2 batteries require the reversible formation/dissolution of sodium superoxide (NaO2) on cycling. Poor cycle life has been associated with parasitic chemistry caused by the reactivity of electrolyte and electrode with NaO2, a strong nucleophile and base. Its reactivity can, however, not consistently explain the side reactions and irreversibility. Herein we show that singlet oxygen (1O2) forms at all stages of cycling and that it is a main driver for parasitic chemistry. It was detected in‐ and ex‐situ via a 1O2 trap that selectively and rapidly forms a stable adduct with 1O2. The 1O2 formation mechanism involves proton‐mediated superoxide disproportionation on discharge, rest, and charge below ca. 3.3 V, and direct electrochemical 1O2 evolution above ca. 3.3 V. Trace water, which is needed for high capacities also drives parasitic chemistry. Controlling the highly reactive singlet oxygen is thus crucial for achieving highly reversible cell operation.

Passivation layers on electrode materials are ubiquitous in nonaqueous battery chemistries and strongly govern performance and lifetime. They comprise breakdown products of the electrolyte including carbonate, alkyl carbonates, alkoxides, carboxylates, and polymers. Parasitic chemistry in metal−O 2 batteries forms similar products and is tied to the deviation of the O 2 balance from the ideal stoichiometry during formation/decomposition of alkaline peroxides or superoxides. Accurate and integral quantification of carbonaceous species and peroxides or superoxides in battery electrodes remains, however, elusive. We present a refined procedure to quantify them accurately and sensitively by pointing out and rectifying pitfalls of previous procedures. Carbonaceous compounds are differentiated into inorganic and organic ones. We combine mass and UV−vis spectrometry to quantify evolved O 2 and complexed peroxide and CO 2 evolved from carbonaceous compounds by acid treatment and Fenton's reaction. The capabilities of the method are exemplified by means of Li−O 2 and Na−O 2 cathodes, graphite anodes, and LiNi 0.8 Co 0.15 Al 0.05 O 2 cathodes.

Aprotische Natrium-O 2 -Batterien basieren auf der reversiblen Bildung und Auflçsung von Natriumsuperoxid (NaO 2 )w ährend des Zellbetriebs.N ebenreaktionen des Elektrolyten und der Elektrode mit dem stark nukleophilen und basischen NaO 2 führen zu mangelhafter Zyklenstabilität.

Polydicyclopentadiene (pDCPD), a thermoset with excellent mechanical properties, has enormous potential as a lightweight, tough, and stable matrix material owing to its highly cross-linked macromolecular network. This work describes generating pDCPD-based foams and hierarchically porous carbons derived therefrom by combining ring-opening metathesis polymerization (ROMP) of DCPD, high internal phase emulsions (HIPEs) as structural templates, and subsequent carbonization. The structure and function of the carbon foams were characterized and discussed in detail using scanning electron, transmission electron, or atomic force microscopy (SEM, TEM, AFM), electron energy-loss spectroscopy (TEM-EELS), N2 sorption, and analyses of electrical conductivity as well as mechanical properties. The resulting materials exhibited uniform, shape-retaining shrinkage of only ∼1/3 after carbonization. No structural failure was observed even when the pDCPD precursor foams were heated to 1400 °C. Instead, the high porosity, void size, and 3D interconnectivity were fully preserved, and the void diameters could be adjusted between 87 and 2.5 μm. Moreover, foams have a carbon content >97%, an electronic conductivity of up to 2800 S·m–1, a Young’s modulus of up to 2.1 GPa, and a specific surface area of up to 1200 m2·g–1. Surprisingly, the pDCPD foams were carbonized into shapes other than monoliths, such as 10’s of micron thick membranes or foamy coatings adhered to a metal foil or grid substrate. The latter coatings even adhere upon bending. Finally, as a use case, carbonized foams were applied as porous cathodes for Li–O2 batteries where the foams show a favorable combination of porosity, active surface area, and pore size for outstanding capacity.