This paper outlines a refrac pilot testing program conducted in the Eagle Ford Shale.As wells in the Eagle Ford accumulate production over time and the pressure around the horizontal wellbore declines, it is important to also consider communication due to offset fracture stimulation. Refracturing trials in older fields, such as the Barnett Shale have yielded a positive enhancement of well performance (Siebrits et al., 2000). This paper evaluates the concept of diverting fluid and proppant along horizontal wells in the Eagle Ford, while considering any communication with older producing wells during refracturing operations.Pumping data acquired during the refracturing is used to explain some of these concepts. Modeling of induced fracture geometry, considering the effect of current pore pressures, is conducted with a fully three-dimensional hydraulic fracture numerical simulator. The pressure of the subject zone may affect the containment and rate of growth of the new fractures, as well as the re-orientation of the existing fractures.Refracturing an old horizontal well with 5,000 ft lateral length and more than 800 existing perforation holes in the casing is very challenging and requires a careful integration of reservoir knowledge, completions skills and experience. The technical team at Pioneer Natural Resources has developed an integrated workflow to design and execute a refracturing job for an Eagle Ford well. The work flow includes: 1) identification of the lower pressure areas along the lateral using surveillance data from the well, such as microseismic, tracer logs, and production data. 2) identifying which wells within the drilling schedule are offsetting older wells that have high cumulative production, and 3) designing a single fracturing job with several sub-stages separated by diverting agents. Each sub-stage is intended to target specific areas along the lateral, which were previously identified as low pressure zones. Volumes and pump schedules will be specific for each candidate and are based on but not limited to proximity to an offset well, lateral length, and existence of geological structures such as faults and fractures in the area. The results from this pilot testing program such as the radioactive tracers and the fracture gradient changes before and after refrac will be evaluated upon completion of the field execution.
Tight oil and shale gas resources produced 29% of total US crude oil and 40% of total US natural gas in 2012 (EIA). Technically recoverable quantities of shale gas and shale oil resources for the US are 665 trillion cubic feet and 58 billion barrels, respectively. Considering the impact of the "unconventional boom" on the economy, it is crucial to understand the production performance of wells to maximize the recovery from shale plays. The latest advances in Rate Transient Analysis (RTA) provide quick yet robust tools to assess the quality of the Stimulated Rock Volume (SRV) and long term performance of the wells by estimating EURs. The most common challenge in history-matching of production in shale gas/oil wells has been the non-uniqueness of the history-matched parameters. A lot of emphasis has been put on estimation of fracture half-length, which is believed to be a primary driver for the performance of shale gas/oil wells. Since linear flow is the main transient flow regime in the early life of a hydraulically-fractured shale gas/oil well, a Rate Normalized Pressure (RNP) versus Square Root of Time plot is the most commonly used diagnostic plot for the performance analysis of the wells. A*sqrt(k) or xf*sqrt(k) parameter groups are reported as a proxy for productivity in hydraulically fractured shale/gas oil wells. Besides having permeability as an unknown, the history-match is also sensitive to net hydraulic fracture height, which is one of the inputs to models that must be specified from other sources of information. This paper presents a novel approach for production performance analysis of shale gas/oil wells, which significantly reduces the non-uniqueness issues that one can have in comparison of performance. Twenty two Eagle Ford Shale wells were analyzed across the trend from lean gas to high-yield condensate to define a workflow that could be applied to other wells in different geologic areas, yet provide consistent comparison of long term performance (EURs).
This paper outlines a refrac pilot testing program conducted in the Eagle Ford Shale. As wells in the Eagle Ford accumulate production over time and the pressure around the horizontal wellbore declines, it is important to also consider communication due to offset fracture stimulation. Refracturing trials in older fields, such as the Barnett Shale have yielded a positive enhancement of well performance (Siebrits et al., 2000). This paper evaluates the concept of diverting fluid and proppant along horizontal wells in the Eagle Ford, while considering any communication with older producing wells during refracturing operations. Pumping data acquired during the refracturing is used to explain some of these concepts. Modeling of induced fracture geometry, considering the effect of current pore pressures, is conducted with a fully three-dimensional hydraulic fracture numerical simulator. The pressure of the subject zone may affect the containment and rate of growth of the new fractures, as well as the re-orientation of the existing fractures. Refracturing an old horizontal well with 5,000 ft lateral length and more than 800 existing perforation holes in the casing is very challenging and requires a careful integration of reservoir knowledge, completions skills and experience. The technical team at Pioneer Natural Resources has developed an integrated workflow to design and execute a refracturing job for an Eagle Ford well. The work flow includes: 1) identification of the lower pressure areas along the lateral using surveillance data from the well, such as microseismic, tracer logs, and production data. 2) identifying which wells within the drilling schedule are offsetting older wells that have high cumulative production, and 3) designing a single fracturing job with several sub-stages separated by diverting agents. Each sub-stage is intended to target specific areas along the lateral, which were previously identified as low pressure zones. Volumes and pump schedules will be specific for each candidate and are based on but not limited to proximity to an offset well, lateral length, and existence of geological structures such as faults and fractures in the area. The results from this pilot testing program such as the radioactive tracers and the fracture gradient changes before and after refrac will be evaluated upon completion of the field execution.
Areas of Southwestern Energy's Fayetteville Shale asset were identified as candidates for optimized completions by analyzing the y-axis intercept of the Rate Transient Analysis (RTA) square root time plot, an indicator of skin, and looking for those wells with values above the field average. It is hypothesized that the increase in the y-intercept from the typical average across the asset is due to proppant embedment in the formation and through optimized completions a reduction in the y-intercept, or skin, can be achieved. The initial test program started in Q4 2014 and the area of interest (AOI) was established by conducting rate transient analysis on all Southwestern Energy Fayetteville Shale wells and then mapping the variable across the play. The initial test pads were located in areas where y-intercept values exceeded average and included 6 pads, 19 wells, with completion designs using 30 - 50% more sand/stage and 7 pads, 24 wells, with 30 - 50% reduction in fluid volume/stage versus the standard Southwestern Energy Fayetteville Shale completion. Success or failure was determined by comparing normalized pressure and well performance to the 9-section area of the test pad. The wells with 30 - 50% more sand/stage have an average EUR/CLAT improvement of 4% and exhibit a reduction of 24% in the y-intercept. The wells with 30 - 50% reduction in fluid volume have an average EUR/CLAT improvement of 6% and exhibit a reduction of 68% in the y-intercept and the economics are more favorable due to the reduced costs of the completion. Given the success of the initial test program in the AOI, more pads are being evaluated to have optimized completions. As the program progresses, the y-intercept will be used in conjunction with data analysis of the more than 3,500 wells currently in the Fayetteville Shale to further optimize completions in specific areas.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.