Hydrogel
bioprinting is a major area of focus in the field of tissue
engineering. However, 3D printed hydrogel scaffolds often suffer from
low printing accuracy and poor mechanical properties because of their
soft nature and tendency to shrink. This makes it challenging to process
them into structural materials. In this study, natural chitosan hydrogel
scaffolds were, for the first time, reinforced with milled silk particles
and fabricated by 3D printing. Compared with pure chitosan scaffolds,
the addition of silk particles resulted in up to a 5-fold increase
in compressive modulus as well as significantly better printing accuracy
and improved scaffold stability. The chitosan/silk inks flowed well
during printing; loading of up to 300% silk (w/w) resulted in only
minor changes in the rheological properties of the ink. Particle loading
also enabled tuning of the surface roughness of the scaffolds and
improved scaffolds’ biodegradability. The printed composite
hydrogel scaffolds showed no cytotoxicity and supported adherence
and growth of human fibroblast cells.
The degumming process to remove sericin decreases silk fiber strength; however, the impact of degumming on the mechanical properties of regenerated silk biomaterials has not been established. This study investigated the effect of degumming temperature, time, alkaline component and alkaline concentration on the mechanical properties of silk fibroin films. Sericin removal was estimated using weight loss; 10 samples with 12.2–29.4% weight loss were then further characterized in terms of fiber mechanical properties, fiber surface morphology, molecular weight distribution and film tensile strength. A negative correlation was found between weight loss and fiber tensile strength. This loss of fiber strength under harsher degumming conditions had a direct impact on the tensile strength of regenerated films. Mild degumming conditions (weight loss of 12.2%) led to higher film strength (8.9 MPa), whereas aggressive degumming conditions (with 29.4% weight loss) resulted in significantly weaker films (4.3 MPa). The presence of some residual sericin, after mild degumming, is likely to affect the mechanical properties of the regenerated silk films. These results will assist in the development of materials with mechanical and biocompatibility properties tuned to specific biomedical applications.
Terrestrial decapods consume a wide variety of plant and animal material. The potential adaptations of carnivorous, omnivorous, and herbivorous terrestrial crustaceans were studied by examining the functional morphology of the gastric mill. Two closely related species from each feeding preference group were examined to identify which features of the mill were due to phylogeny and which were due to adaptation. The morphology of the gastric mill matched the diet well; the gastric mills of the carnivorous species (Geograpsus grayi and Geograpsus crinipes) possessed a blunt, rounded medial tooth and flattened lateral teeth with a longitudinal grinding groove. These features make them well suited to a carnivorous diet of soft animal tissue as well as hard material, such as arthropod exoskeleton. In contrast, the mill of the herbivorous gecarcinids (Gecarcoidea natalis and Discoplax hirtipes) consisted of a medial tooth with sharp transverse ridges and lateral teeth with sharp interlocking cusps and ridges and no grinding surface. These features would efficiently shred fibrous plant material. The morphology of the mill of the omnivorous coenobitids (Coenobita perlatus and Birgus latro) was more generalized toward a mixed diet. However, the mill of B. latro was more adapted to deal with highly nutritious food items, such as nuts and heavily calcified decapods. Its mill possessed lateral teeth with extended ridges, which sat close to the calcified cardiopyloric valve to form a flattened floor. Hard items trapped in the mill would be crushed against this surface by the medial tooth.
SUMMARY 2.1.4) from G. natalis had a molecular mass of 52 kDa and an optimum pH of 4-7. It mainly hydrolysed β-1,4-glycosidic bonds, but was also capable of significant hydrolysis of β-1,3-glycosidic bonds. Two endo-β-1,4-glucanases, termed 1 and 2, with respective molecular masses of 53±3 and 52 kDa, were purified from C. destructor. Endo-β-1,4-glucanase 1 was only capable of hydrolysing β-1,4-glycosidic bonds and had an optimum pH of 5.5. Endo-β-1,4-glucanases from both species produced some glucose, cellobiose and other short oligomers from the hydrolysis of carboxymethyl cellulose.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.