Saat ini berbagai upaya dilakukan untuk mengurangi penebangan pohon secara berlebihan yang digunakan sebagai bahan baku dalam pembuatan papan, meja, kurs dan lain-lain. Alternatif yang digunakan untuk mengurangi penebangan berlebihan ini dengan memanfaatkan sumber daya yang terdapat dilaut daun lamun yang dapat dimanfaatkan oleh masyarakat sebagai penyaring limbah,stabilizator pantai,bahan untuk pabrik kertas dan sumber bahan kimia yakni. Dalam penelitian ini daun lamun diambil serat sebagai bahan material unutk mengganti bahan dasar yang masih menggunakan kayu. Tujuan dari penelitian ini adalah mengetahui pengaruh penambahan volume serat daun lamun (Enhalus acoroides) dan mengetahui persentasi volume serat daun dengan karakter yang bagus berdasarkan sifat mekanik dan sifat fisik. Dalam penelitian ini menggunakan metode eksperimen yang dilakukan untuk pengujian spesimen. Dari hasil yang diperoleh bahwa nilai kekuatan impak maksimal terdapat pada komposit dengan serat 50% sebesar 6,36 (J/mm2) dan minimal terdapat pada komposit dengan serat 10% sebesar 1,758 (J/mm2). Dan persentasi volume serat daun lamun (Enhalus acoroides) memebrikan hasil yang maksimal pada fraksi volume serat 50% dan minimal pada fraksi volume 10%.
Serat ampas sagu merupakan sissa dari pengolahan sagu yang biasa dipergunakan sebagai bahan pakan ternak olehmasyarakat setempat. Dalam penelitian ini serat empulur sagu akan dikembangkan menjadi bahan komposit yang dapatdipergunakan sebagai material dalam bidang teknik.Penelitian dilakukan secara eksperimental untuk mengetahui pengaruh fraksi volume antara serat empelur sagu danresin polyester terhadap nilai kekuatan tarik dan kekuatan bending material komposit dengan variable pengujian fraksivolume serat empelur sagu 10%, 20%, 30 % dan 40 %.Hasil pengujian menunjukan bahwa nilai kekuatan tarik dan bending komposit mengalami peningkatan sesuai denganperubahan fraksi volume serat serat empelur sagu. Dimana nilai tertinggi untuk kekuatan tarik yaitu 10,4 MPa padafraksi volume 40 % dan terendah pada fraksi volume 10 % yaitu 6,03 MPa.Untuk hasil pengujian bending nilai tertinggi berada pada fraksi volume 40 % sebesar 2,86 MPa dan nilai terendahberada pada fraksi volume 10 %, sebesar 2,02 MPa. Peningkatan kekuatan tarik dan bending secara umumdipengaruhi oleh daya ikat antara serat dengan matriks yang sempurna serta penambahan volume fraksi serat EmpelurSagu pada komposit.
Tanah liat adalah bahan dasar membuat bata merah yang sumber daya alamnya melimpah di maluku, sedangkan serat sabut kelapa adalah merupakan potensi limbah alam yang sampai sekarang belum dikaji secara ilmiah dan dimanfaatkan untuk suatu tipe material. Sedangkan pati sagu dalam penelitian ini digunakan sebagai perekat yang nantinya dipakai pada saat pembuatan bata merah. Penelitian ini menggunakan metode Hand Lay Up, dalam pembuatan komposit serat tunggal dengan variasi fraksi volume tanah liat : serat sabut kelapa : matrik pati sagu yaitu, 50%:10%:40%, 50%:20%:30%, 50%:30%:20%, dan 50%:40%:10%. Komposisi komposit dibuat sesuai variasi fraksi volume yang sudah ditentukan, dan dicetakan dengan cara manual. Setelah itu specimen di keringkan pada suhu 130⁰C, selama 1 jam, kemudian dilakukan uji impak. Hasil penelitian adalah terjadi kenaikan kekuatan impak seiring penambahan fraksi volume, dimana energi impak tertinggi untuk fraksi volume 50% : 40%:10%, sebesar 2.38 J, dan energi impak terendah pada fraksi volume 50% : 10%:40%, sebesar 1.67 J. dan harga impak tertinggi untuk fraksi volume 50% : 40%:10%, sebesar 0.030 J/mm2, dan energi impak terendah pada fraksi volume 50% :10%:40%, sebesar 0.021 J/mm2. Sehingga dapat disimpulkan bahwa kekuatan impak komposit serat sabut kelapa dan tanah liat yang diperkuat pati sagu mengalami peningkatan seiring dengan bertambahnya fraksi volume serat.
Durian rind fiber composite as a reinforcement is one of the interesting research areas. Some of the advantages associated with using natural fibers due to reinforcement in polymers are their non-abrasive properties and low-cost consumption. Durian rind when processed further can be made into cellulose fiber which can be used as a natural filler in unsaturated polyester composites. Among various types of natural fibers, durian skin fiber is an alternative polymer composite filler. Durian skin can be obtained easily because it is a family waste that has not been used. To get a new composite material made from durian skin waste, and to help the community and government in handling durian skin waste. The purpose of this study was to determine the maximum value of the variation of the volume fraction of durian skin fiber on the impact strength and hardness strength according to the desired application. This study uses the Hand Lay Up method, in the manufacture of single fiber composites with variations in volume fraction of durian skin fiber: polyester matrix, namely, 10%: 90%, 20%: 80%, 30%: 70%, 40%: 60% and 50 %:50%. The results showed that there was an increase in the impact strength and hardness strength with the addition of the volume fraction, where the highest impact energy for the volume fraction of durian skin fiber was 50%: 50%, 0.7738 J, and the highest impact value was 0.0096725 J/mm² and energy the lowest impact is 10%: 90%, 0.461 J. and the lowest impact price is 0.0057685 J/mm². So it can be concluded that the impact strength and hardness of the durian skin fiber composite increased with the increase in the volume fraction of the fiber.
Abstrak Penelitian ini dibuat untuk mengetahui getaran vertical direct inline dari suatu mekanisme ekivalen cam follower dengan profil cam harmonik pada suatu manifold -valve train motor diesel. Masalahnya dimulai dengan penentuan koefisien redaman viscous dan koefisien kekakuan pegas ekivalen sistem yang mana sulit ditentukan secara langsung. Oleh karena secara praktis dapat dipandang bahwa sinyal sistem adalah bersifat deterministick random process maka untuk mengatasi kesulitan ini dilakukan suatu analisa gabungan deduksi dan induksi yaitu dalam model estimasi ordinary least square (OLS) dan simulasi numerik Newton-Rhapson dengan mengacu pada data record hasil pengukuran eksperimental respon getaran yang ditunjukkan oleh sensor accelerometer. Sinyal getaran respon sistem dengan model mekanik single degree of freedom (1-dof) ini kenudian diolah baik dalam domain waktu atau domain frekuensi dengan menerapkanLaplace Transform dan Fast Furrior Transform (FFT). Hasilnya menunjukan bahwa komputasi numerik itu dapat dibuat untuk mengetahui harga-harga koefisien redaman viscous ekivalen, koefisien kekakuan pegas ekivalen dan initial tensiom clearance ekivalen sedemikian hingga selanjutnya respon dinamik sinyal getaran sistem dapat diestimasi dengan menerapkan metode simulasi numerik Runge-Kutta order ke-empat. Algoritma hasil formulasinya dengan demikian dapat menjadi lebih general untuk menjawab berbagai persoalan amplitude getaran pada level data percepatan eksitasi ekivalen multi input multi output (MIMO) dalam berbagai variasi sistem cam-follower yang diberikan sebagaimana dimaksud.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.