Quartz cementation in sandstones is closely linked to grain coating phases and diagenetic alteration. Grain coatings consisting of illite smectite stained with iron oxides and hydroxides are able to preserve large amounts of porosity by preventing the formation of syntaxial quartz overgrowth cement. The Penrith Sandstone Formation was chosen as an analogue for Rotliegend reservoirs to test the impact of grain coatings on quartz cementation. This adds to an existing model of cementation. Differences of grain coating coverage can be linked to grain size. Extensive grain coatings are present in finer grained laminae in some samples. Coarser grained laminae contain less extensive grain coatings. The analysis of grain coatings based on standard petrographic analyses is combined with high resolution QEMSCAN® analyses. Structural features include deformation bands of different ages. Diagenetic alterations around faults, recorded by grain coatings, allow the delineation of relative temporal relations, revealing at least two generations of deformation band formation associated with normal faulting. In the Vale of Eden succession one normal faulting event postdates burial diagenetic quartz cementation as is evident by fault focused fluid flow and associated bleaching of iron and absence of quartz overgrowth. Repository KITopenDies ist ein Postprint/begutachtetes Manuskript.

Present work investigates the dynamics of polycrystalline quartz cement growth in sandstone using a multiphase‐field model. First, the model parameters corresponding to common reservoir temperature and pressure conditions were determined. A parameter related to growth kinetics was ascertained through undisturbed cement growth simulations to aptly capture the known faceting‐dependent growth behavior of quartz. Unrestricted growth simulations for different grain sizes, number of subgrains, and their crystallographic orientations revealed that (I) the model successfully recovers the tendency of quartz cements to grow at a faster overall rate on a coarse grain as compared to finer one and (II) the impact of crystallographic orientations of individual subgrains in polycrystalline grains on cement volume increases with increasing number of subgrains. For applying the model to realistic multigrain systems, we generated digital grain packs through a systematic procedure. These packs fairly represent natural sandstone in terms of grain shapes, sizes, and depositional porosity. The simulated textures in these packs resemble natural samples in terms of crystal morphologies and pore geometries. The cement growth rate decreases with the increase in fraction of polycrystalline grains, indicating a significant role of mutual hindrance among differently oriented overgrowths originating from different subgrains. Further, the permeabilities computed using fluid‐flow simulations through the progressively cemented packs suggest that monocrystalline packs are more permeable than equally porous polycrystalline ones. The computed permeabilities of the simulated microstructures are consistent with the measured permeabilities, advocating the pack generation process and cementation modeling approach.

No abstract

No abstract

Reservoir quality of sandstones is mainly derived from their permeability and porosity. As a result, porosityreducing processes need to be understood in order to evaluate and model reservoir quality in sandstones. This case study from a Rotliegend gas reservoir in the Northern German Basin utilizes petrophysical measurements in conjunction with petrography in order to assess reservoir qualities and define rock types. The most significant diagenetic factors influencing the development of the IGV (intergranular volume) are quartz cementation due to low illite grain coating coverages on grain to IGV interfaces and chemical compaction due to pronounced illite grain coating coverages on grain to grain interfaces. Where large proportions of the interface between adjacent grains are coated by illite, stronger chemical compaction (pressure dissolution) was observed to occur. This chemical compaction reduces the IGV, and thus open pore space.Permeabilities measured under decreasing confining pressures from 50 to 2 MPa were used to determine the pressure sensitivities of permeability (David et al., 1994), which ranged from 0.005 to 0.22 MPa −1 . The pressure sensitivity of permeability, porosity and permeability were linked to the petrographic texture, implying three different major rock types: Type A is characterized by an uncemented petrographic texture with high porosities (avg.: 9.8%), high permeabilities (avg.: 126 mD), and low pressure sensitivities of permeability (avg.: 0.019 MPa −1 ). Type B is intensely cemented with reduced porosities (avg.: 4.0%), reduced permeabilities (avg.: 0.59 mD), and increased pressure sensitivities of permeability (avg.: 0.073 MPa −1 ). Type C is characterized by intense chemical compaction leading to the lowest porosities (avg.: 1.8%) and permeabilities (avg.: 0.037 mD) in concert with the highest pressure sensitivity of permeability (avg.: 0.12 MPa −1 ). The heterogeneity induced by diagenesis will have an impact on recoverable resources and flow rates in both hydrocarbon and geothermal projects in similar siliciclastic reservoirs.

No abstract

This paper investigates reservoir quality development in tight Upper Carboniferous fluvial sandstones (Westphalian C/D) in the Lower Saxony Basin, NW Germany. The study integrates data from three outcrops (Piesberg, Woitzel and Hüggel) in the south of the basin with that from two wells (Wells A and B) located at gas fields approximately 50 km to the north. Petrographic and petrophysical data are related to the diagenetic evolution of the sandstones and the burial and structural history of the Lower Saxony Basin. The outcrop and subsurface data sets are compared in order to investigate the factors controlling reservoir quality evolution. Upper Carboniferous fluvial sandstones from the Woitzel and Hüggel outcrops and from Wells A and B have similar matrix permeabilities (0.01 to 10 mD), but matrix porosities vary between Well A (average 6%), Well B (average 10%), Woitzel (average 15%), and Hüggel (average 19%). Permeability reduction during burial is related to the formation of clay mineral cement, which was mainly controlled by variations in both the palaeo‐climate and in the sandstones’ depositional composition. Matrix porosity was controlled by local differences in burial history related to basin inversion tectonics. The greater amount of inversion‐related uplift at Well B (about 2.8 km) resulted in lower thermal exposure of the Westphalian sandstones at this location, which thus show higher matrix porosities than the sandstones at Well A which were uplifted by only about 1.2 km. Further increases in porosity in the outcrop sandstones may be related to the dissolution of carbonate cement during late‐stage uplift in near‐surface conditions. Upper Carboniferous fluvial sandstones from the Piesberg quarry show the poorest reservoir characteristics compared to the samples from the subsurface and the other outcrops, with matrix porosities averaging 6% and permeabilities <0.01 mD. Reservoir quality reduction was controlled by thermal anomalies associated with a large fault at the Piesberg quarry. By contrast, a few outliers in the sample data sets from Well B and the Piesberg quarry, which have permeabilities of more than 100 mD, show that faulting or natural fracturing may enhance reservoir quality within a particular area. Faults/fractures may act as potential migration pathways for leaching fluids, or may provide fracture‐permeability systems with production potential. Depositional setting, burial‐related diagenetic processes and structural characteristics in the Lower Saxony Basin need to be carefully evaluated in order to provide an improved understanding of the reservoir quality of the Upper Carboniferous sandstones.

No abstract