The swelling behavior of poly(2-(diethylamino)ethyl methacrylate) (PDEA) brushes in response to changes in solution pH and ionic strength has been investigated. The brushes were synthesized by ARGET ATRP methodology at the silica-aqueous solution interface via two different surface-bound initiator approaches: electrostatically adsorbed cationic macroinitiator and covalently anchored silane-based ATRP initiator moieties. The pH-response of these brushes is studied as a function of the solvated brush thickness in a constant flow regime that elucidates the intrinsic behavior of polymer brushes. In situ ellipsometry equilibrium measurements show the pH-induced brush swelling and collapse transitions are hysteretic in nature. Furthermore, high temporal resolution kinetic studies demonstrate that protonation and solvent ingress during swelling occur much faster than the brush charge neutralization and solvent expulsion during collapse. This hysteresis is attributed to the formation of a dense outer region or skin during collapse that retards solvent egress. Moreover, at a constant pH below its pKa, the PDEA brush exhibited a critical conformational change in the range 0.5-1 mM electrolyte, a range much narrower than predicted by the theory of the osmotic brush regime. This behavior is attributed to the hydrophobicity of the collapsed brush. The swelling and collapse kinetics for this salt-induced transition are nearly identical. This is in contrast to the asymmetry in the rate of the pH-induced response, suggesting an alternative mechanism for the two processes dependent on the nature of the environmental trigger.

The solvation and swelling behaviour of three dialkylaminoethyl methacrylate polymer brushes, of varying hydrophobicity, have been investigated using a combination of in situ ellipsometry and a quartz crystal microbalance with dissipation (QCM-D). At low pH the tertiary amine groups of the three polymers are protonated and all three brushes are significantly solvated and swell by adopting an extended conformation. As the pH is increased the weak polybasic brushes become increasingly deprotonated and collapse via solvent expulsion. By employing high temporal resolution measurements we have found that monomer hydrophobicity has a direct influence on the dynamics of this pH-response. The most hydrophobic poly(2-diisopropylamino)ethyl methacrylate (poly(DPA)) brush exhibits the fastest maximum swelling rate. This maximum swelling rate is reduced with decreasing monomer hydrophobicity for the 2-diethylamino, and even further for the 2-dimethylamino analogues. For all three brushes, the corresponding collapse transition is slower and compounded by an induction time that decreases with monomer hydrophobicity. Here also, the maximum collapse rate is greatest for the most hydrophobic polymer. This domination of the pH-response kinetics by monomer hydrophobicity is attributed to attractive hydrophobic forces between polymer segments overcoming the repulsive electrostatic forces between the tertiary amine residues.

The effect of anion identity and temperature on the internal nanostructure of poly(N-isopropylacrylamide) brushes were investigated using neutron reflectometry (NR), atomic force microscopy (AFM) and quartz crystal microbalance with dissipation monitoring (QCM-D). NR and QCM-D measurements showed that addition of strongly kosmotropic acetate anions shifted the lower critical solution temperature (LCST) to lower temperatures relative to pure D2O/H2O, while strongly chaotropic thiocyanate anions shifted the LCST to higher temperatures. Polymer density profiles derived from NR showed direct evidence of vertical phase separation at temperatures around the LCST in all conditions. Results indicate that the density profiles were not simple modulations of structures observed in D2O to higher or lower temperatures, with both anion identity and ionic strength found to influence the qualitative features of the profiles. In particular, the presence of thiocyanate broadened the LCST transition which is attributed to the ability of the thiocyanate anion to electrosterically stabilize the brush above its LCST. Complementary AFM data showed that the acetate ion induced collapsed structures while a broader transition is observed in the presence of thiocyanate.

The influence of specific anions on the equilibrium thermoresponse of poly(N-isopropylacrylamide) (pNIPAM) brushes has been studied using in situ ellipsometry, quartz crystal microbalance with dissipation (QCM-D) and static contact angle measurements between 20 and 45 °C in the presence of up to 250 mM acetate and thiocyanate anions in water. The thickness and changes in dissipation exhibited a broad swelling transition spanning approximately 15 °C from collapsed (high temperatures) to swollen conformation (low temperatures) while the brush surface wettability changed over approximately 2 °C. In the presence of the kosmotropic acetate anions, the measured lower critical solution temperature (LCST) by the three techniques was very similar and decreased linearly as a function of ionic strength. Conversely, increasing the concentration of the chaotropic thiocyanate anions raised the LCST of the pNIPAM brushes with variation in the measured LCST between the three techniques increasing with ionic strength. The thickness of the pNIPAM brush was seen to progressively increase with increasing thiocyanate concentration at all temperatures. It is proposed that specific ion binding of the chaotropic thiocyanate anion with pNIPAM amide moieties increases the electrostatic intra- and intermolecular repulsion within and between pNIPAM chains. This allows the brush to begin to swell at higher temperatures and to an overall greater extent.

The anion-specific solvation and conformational behavior of weakly basic poly(2-dimethylamino)ethyl methacrylate (poly(DMA)), poly(2-diethylamino)ethyl methacrylate (poly(DEA)), and poly(2-diisopropylamino)ethyl methacrylate (poly(DPA)) brushes, with correspondingly increasing inherent hydrophobicity, have been investigated using in situ ellipsometric and quartz crystal microbalance with dissipation (QCM-D) measurements. In the osmotic brush regime, as the initial low concentration of salt is increased, the brushes osmotically swell by the uptake of solvent as they become charged and the attractive hydrophobic inter- and intrachain interactions are overcome. With increased ionic strength, the brushes move into the salted brush regime where they desolvate and collapse as their electrostatic charge is screened. Here, as the brushes collapse, they transition to more uniform and rigid conformations, which dissipate less energy, than similarly solvated brushes at lower ionic strength. Significantly, in these distinct regimes brush behavior is not only ionic strength dependent but is also influenced by the nature of the added salt based on its position in the well-known Hofmeister or lyotropic series, with potassium acetate, nitrate, and thiocyanate investigated. The strongly kosmotropic acetate anions display low affinity for the hydrophobic polymers, and largely unscreened electrosteric repulsions allow the brushes to remain highly solvated at higher acetate concentrations. The mildly chaotropic nitrate and strongly chaotropic thiocyanate anions exhibit a polymer hydrophobicity-dependent affinity for the brushes. Increasing thiocyanate concentration causes the brushes to collapse at lower ionic strength than for the other two anions. This study of weak polybasic brushes demonstrates the importance of all ion, solvent, and polymer interactions.