In recent years, most cities have faced great demand for electricity supply due to rapid population growth and industrialization. Supplying sufficient electrical energy, while reducing greenhouse gas emissions, is one of the major concerns of policymakers and scientists all over the world. In Saudi Arabia, local authorities are increasingly aware of the necessity of reducing the environmental impact of nonrenewable energy by exploring alternative sustainable energy sources and improving buildings’ energy efficiency. Recently, building-integrated photovoltaic (BIPV) technology has been regarded as a promising technology for generating instantaneous sustainable energy for buildings. To achieve a substantial contribution regarding zero energy buildings, solar energy should be widely used in residential buildings within the urban context. This paper examines how to achieve an appropriate model for integrating photovoltaics on the rooftop of residential buildings in Hail city to provide alternative energy sources. The estimated rooftop areas in Hail city, utilizable for PV application were calculated. Using PV*SOL simulation software, the performance ratio and the system efficiency, as well as the annual energy output in several tilt angles, were determined and presented. The amount of energy expected when using all effective roof area in the city was also calculated. The amount of CO2 emissions that could be reduced as a result of using a PV system was estimated. The results show a significant area of rooftop suitable for PV system in residential buildings in Hail city, which exceeds 9 million square meters. On the other hand, the performance ratio and the system efficiency are affected by the tilt angle of the PV module, where the efficiency increases with higher tilt angle, this is due to the PV module temperature, where, with the decrease in the PV module temperature its efficiency increases. The results indicate that the 30° tilt PV produced the highest amount of energy, whereas the 75° tilt PV records the smallest one although it achieves the best possible efficiency. There is a significant amount of energy produced from the use of all residential rooftops in Hail, and there is also a significant reduction in the amount of CO2 emissions. It is expected that this research would develop innovative building design strategies and specifications allowing for better climate and energy efficiency as well.
The problem of metal-induced toxicity is proliferating with an increase in industrialization and urbanization. The buildup of metals results in severe environmental deterioration and harmful impacts on plant growth. In this study, we investigated the potential of two ornamental plants, Catharanthus roseus (L.) G.Don and Celosia argentea L., to tolerate and accumulate Ni, Cr, Cd, Pb, and Cu. These ornamental plants were grown in Hoagland’s nutrient solution containing metal loads (50 µM and 100 µM) alone and in combination with a synthetic chelator, ethylenediaminetetraacetic acid (EDTA) (2.5 mM). Plant growth and metal tolerance varied in both plant species for Ni, Cr, Cd, Pb, and Cu. C. roseus growth was better in treatments without EDTA, particularly in Ni, Cr, and Pb treatments, and Pb content increased in all parts of the plant. In contrast, Cd content decreased with EDTA addition. In C. argentea, the addition of EDTA resulted in improved plant biomass at both doses of Cu. In contrast, plant biomass reduced significantly in the case of Ni. In C. argentea, without EDTA, root length in Cd and Cu treatments was significantly lower than the control and other treatments. However, the addition of EDTA resulted in improved growth at both doses for Pb and Cu. Metal accumulation in C. argentea enhanced significantly with EDTA addition at both doses of Cu and Cd. Hence, it can be concluded that EDTA addition resulted in improved growth and better metal uptake than treatments without EDTA. Metal accumulation increased with EDTA addition compared to treatments without EDTA, particularly for Pb in C. roseus and Cu and Cd in C. argentea. Based on the present results, C. roseus showed a better ability to phytostabilize Cu, Cd, and Ni, while C. argentea worked better for Ni, Cd, Cu, and Pb.
The repairing process of structures using bonding of composite materials is an efficient and economic way of increasing service life of damaged structures. The finite element method is developed and applied to assist in the design, assessment and optimization of the proposed plans before they are implemented, therefore reducing cost and time. In this study, the finite element method is used to analyze the behavior of a repaired crack using single and double circular composite patches by determining the stress intensity factor reduction. The effects of geometrical and mechanical properties of the patch on the fracture parameters are highlighted. The results show that the thickness gain and the reduction of the asymptotic value of the SIF in the case of the double patch is 7% when compared to the single one. Thus, the gain in the thickness decreases when the thickness of the bonded patch increases up to a value eP = 0.8 mm and beyond this value, it starts increasing. However, an inverse behavior occurs for the mixed mode. In addition, whatever is the size of the strengthened crack, the gain in thickness exceeds 16% in mode I and 20% in mixed mode.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.