No abstract

Squeeze film dampers (SFDs) reduce vibrations and aid in suppressing instabilities in high performance rotor-bearing systems. However, air ingestion and entrapment, pervasive in open-ended dampers with low supply pressures, leads to a bubbly lubricant that severely reduces the dynamic film forces and the overall damping capability. Analyses based on conventional film rupture models, vapor or gaseous lubricant cavitation, fail to predict the actual performance of SFDs, and thus lack credibility in engineering practice. A modified Reynolds equation for prediction of the pressure in a homogeneous bubbly mixture flow is advanced along with an empirical formula for estimation of the amount of air entrained in an open-ended damper. Careful experimentation in a test SFD operating with controlled bubbly mixtures and freely entrained air evidenced similar physical behavior, guided the analytical developments, and provided the basis for validation of the model forwarded. Comparisons of predictions and test results show a fair correlation. A simple equation to predict the amount of air ingestion is also advanced in terms of the damper geometry, supplied flow and operating conditions. The criterion may lack practical implementation since the persistence of air entrainment increases with the frequency and amplitude of journal motions, unless enough lubricant is supplied at all operating conditions.

No abstract

Hydrodynamic instability growth of capsule support membranes (or “tents”) has been recognized as one of the major contributors to the performance degradation in high-compression plastic capsule implosions at the National Ignition Facility (NIF) [E. M. Campbell et al., AIP Conf. Proc. 429, 3 (1998)]. The capsules were supported by tents because the nominal 10-μm diameter fill tubes were not strong enough to support capsules by themselves in indirect-drive implosions on NIF. After it was recognized that the tents had a significant impact of implosion's stability, new alternative support methods were investigated. While some of these methods completely eliminated tent, other concepts still used tents, but concentrated on mitigating their impact. The tent-less methods included “fishing pole” reinforced fill tubes, cantilevered fill tubes, and thin-wire “tetra cage” supports. In the “fishing pole” concept, a 10-μm fill tube was inserted inside 30-μm fill tube for extra support with the connection point located 300 μm away from the capsule surface. The cantilevered fill tubes were supported by 12-μm thick SiC rods, offset by up to 300 μm from the capsule surfaces. In the “tetra-cage” concept, 2.5-μm thick wires (carbon nanotube yarns) were used to support a capsule. Other concepts used “polar tents” and a “foam-shell” to mitigate the effects of the tents. The “polar tents” had significantly reduced contact area between the tents and the capsule compared to the nominal tents. In the “foam-shell” concept, a 200-μm thick, 30 mg/cc SiO2 foam layer was used to offset the tents away from the capsule surface in an attempt to mitigate their effects. These concepts were investigated in x-ray radiography experiments and compared with perturbations from standard tent support. The measured perturbations in the “fishing pole,” cantilevered fill tube, and “tetra-cage” concepts compared favorably with (were smaller than) nominal tent perturbations and were recommended for further testing for feasibility in layered DT implosions. The “polar tents” were tested in layered DT implosions with a relatively-stable “high-foot” drive showing an improvement in neutron yield in one experiment compared to companion implosions with nominal tents. This article reviews and summarizes recent experiments on these alternate capsule support concepts. In addition, the concept of magnetic levitation is also discussed.

Rotor-bearing systems supported on squeeze film dampers (SFDs) show large amplitude vibratory motions when traversing critical speeds. At these operating conditions air is drawn into the damper thin film clearance generating a bubbly mixture with the lubricant and producing SFD forces not readily predictable with currently available analysis. A continuum model is proposed for describing the motion of a bubbly fluid in an open ended SFD operating with circular centered journal orbits. Computed predictions for peak-peak dynamic pressures and fluid film forces agree reasonably well with experimental measurements conducted on a SFD test rig operating with a controlled air in oil mixture. The bubbly flow model provides an initial procedure towards the reliable design of SFDs in actual operating conditions. [S0742-4787(00)02601-1]

Experimental results from indirectly driven inertial confinement fusion experiments testing the performance gained from using an alternate capsule tent support are reported. The polar tent describes an alternate geometry for the thin membrane used to support the Deuterium–Tritium (DT) filled capsule. Here, the contact area is reduced by 23 times by locating the tent support close to the poles of the capsule. The polar tent experiments are repeats of previous 3 shock 1.63 MJ, 400 TW high foot experiments and use a 165 μm thick silicon doped carbon hydrogen plastic (CH) shell. Using the polar tent support, we report a DT neutron yield of 1.07 ×1016, 76% higher than the expected YDT∝V7.7 scaling. This is, at the time of writing, the highest neutron yield to date from a CH shell implosion. Furthermore, we find that the inferred pressure when using the polar tent is significantly above the model based on analytic scaling even when accounting for tent effects. Analysis of x-ray and neutron images shows the reduction of lobes produced by nominal tent features. The reduction of these features in the polar tent experiments leads to decreased low mode (P2 and P4) asymmetry compared to the nominal tent results.

This study aims at analysing the determinants of the premium paid in European banking mergers and acquisitions (M&A). This analysis will highlight the reasons for the bank M&A wave during the 1990s. The empirical study analyses a sample of 81 European banking mergers and acquisitions from 1994 to 2000. The results show that there are different variables that make the target bank attractive for the acquirer, such as the percentage of equity, the percentage of loans and financial profitability. However, geographical and product diversification have not been considered by the acquirers as a reason to pay higher premiums. Moreover, when analysing a sub-sample of savings banks and cooperatives, it is found that M&A deals have been used as a protection measure to avoid being acquired, since these acquisitions aim at attaining a great size, what implies higher premiums are paid for mergers between equals, for acquisitions of higher banks and by those who show lower growth.

In indirectly driven Inertial Confinement Fusion implosions conducted on the National Ignition Facility (NIF), the imploding capsule is supported in a laser-heated radiation enclosure (called a “hohlraum”) by a pair of very thin (∼15–45 nm) plastic films (referred to as a “tent”). Even though the thickness of these tents is a small fraction of that of the spherical capsule ablator (∼165 μm), both numerical simulations as well as experiments indicate that this capsule support mechanism results in a large areal density (ρR) perturbation on the capsule surface at the contact point where the tent departs from the capsule. As a result, during deceleration of the deuterium-tritium (DT) fuel layer, a jet of the dense ablator material penetrates and cools the fuel hot spot, significantly degrading the neutron yield (resulting in only ∼10%–20% of the unperturbed 1-D yield). In this article, we present a hypothesis and supporting design simulations of a new “polar contact” tent support system, which reduces the contact area between the tent and the capsule and results in a significant improvement in the capsule performance. Simulations predict a ∼70% increase in neutron yield over that for an implosion with a traditional tent support. An initial demonstration experiment was conducted on the NIF and produced highest ever recorded primary DT neutron yield among all layered DT implosions with plastic ablators on the NIF, though more experiments are needed to comprehensively study the effect of the polar tent on implosion performance.