The production of synthetic materials generally uses non-renewable forms of energy, which are highly polluting. This is driving the search for natural materials that offer properties similar to synthetic ones. In particular, the use of natural lignocellulosic fibers (NLFs) has been investigated since the end of 20th century, and is emerging strongly as an alternative to replace synthetic components and reinforce composite materials for engineering applications. NLFs stand out in general as they are biodegradable, non-polluting, have comparatively less CO2 emission and are more economically viable. Furthermore, they are lighter and cheaper than synthetic fibers, and are a possible replacement as composite reinforcement with similar mechanical properties. In the present work, a less known NLF from the Amazon region, the ubim fiber (Geonoma bacculifera), was for the first time physically characterized by X-ray diffraction (XRD). Fiber density was statistically analyzed by the Weibull method. Using both the geometric method and the Archimedes’ technique, it was found that ubim fiber has one of the lowest densities, 0.70–0.73 g/cm3, for NLFs already reported in the literature. Excluding the porosity, however, the absolute density measured by pycnometry was relatively higher. In addition, the crystallinity index, of 83%, microfibril angle, of 7.42–7.49°, and ubim fiber microstructure of lumen and channel pores were also characterized by scanning electron microscopy. These preliminary results indicate a promising application of ubim fiber as eco-friendly reinforcement of civil construction composite material.

The search for unexplored natural materials as an alternative to synthetic components has driven the development of novel polymeric composites reinforced with environmentally-friendly materials. Natural lignocellulosic fibers (NLFs) have been highlighted as potential reinforcement in composite materials for engineering applications. In this work, a less known Amazonian fiber, the ubim fiber (Geonoma baculifera), is investigated as a possible reinforcement in epoxy composites and was, for the first time, thermally characterized by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Additionally, its chemical structure was elucidated by Fourier transform infrared spectroscopy (FTIR). Ballistic tests were also performed against the threat of a 7.62 mm high-speed lead projectile. The results were statistically analyzed by the Weibull statistical analysis method. FTIR analysis showed the functional groups normally found for NLFs highly rich in cellulose, hemicellulose, and lignin. The TGA/DTG results showed the onset of thermal degradation for the composites (325~335 °C), which represents better thermal stability than isolated ubim fiber (259 °C), but slightly lower than that of pure epoxy (352 °C). The DSC results of the composites indicate endothermic peaks between 54 and 56 °C, and for the ubim fibers, at 71 °C. Ballistic tests revealed higher energy absorption in composites with lower fiber content due to the more intense action of the brittle fracture mechanisms of the epoxy resin, which tended to dissipate more energy. These failure mechanisms revealed the presence of river marks, cracks, and broken fibers with a detachment interface. These results may contribute to the production of ubim fiber-reinforced composites in engineering applications, such as ballistic armors.

This article presents a comprehensive study on the physical, mechanical, thermal, and chemical properties of polypropylene (PP) composites reinforced with hemp fibers (HF) and compatibilized with maleic anhydride (MAPP). The composites were processed using a twin-screw extruder, followed by hot compression at 190 °C. Subsequently, the composites were analyzed using Izod impact and Shore D hardness tests to evaluate their mechanical properties. Thermal properties were investigated through differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), while X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR) were employed to study their chemical properties. Additionally, a statistical analysis was conducted to compare the average results of the impact and hardness tests. XRD analysis revealed that the addition of HF and MAPP led to the disappearance of peaks corresponding to the beta phase in pure PP. Hemp fibers exhibited an impressive crystallinity of 82.10%, surpassing other natural fibers, and had a significant molecular orientation angle (MFA) of 6.06°, making them highly desirable for engineering applications. The crystallite size was observed to be relatively large, at 32.49 nm. FTIR analysis demonstrated strong interactions between the fiber, compatibilizing agent, and polymer matrix. TGA tests showed that the addition of 5 and 10 wt.% MAPP resulted in complete degradation of the composites, similar to pure PP. DSC analyses indicated a reduction in crystallinity (Xc) due to the incorporation of HF and MAPP. Shore D hardness tests revealed an increase in hardness with the addition of 5 wt.% MAPP, while a steep decline in this property was observed with 10 wt.% MAPP. In terms of impact resistance, fractions of 3 and 5 wt.% MAPP in the composites exhibited improved performance compared to the pure polymer. Analysis of variance (ANOVA) was employed to ensure the statistical reliability of the mechanical test results. This comprehensive study sheds light on the diverse properties of PP composites reinforced with hemp fibers and compatibilized with MAPP, emphasizing their potential as sustainable materials for engineering applications. The results contribute to the understanding of the structural and functional aspects of these composites, guiding future research and developments in the field.

No abstract

RESUMO:O presente estudo propõe uma nova rota de produção de óxido de grafeno reduzido (rGO), empregando agentes antioxidantes presentes no suco da laranja-pera. Os agentes redutores presentes no suco da laranja natural e processado possuem importantes substâncias bioativas com função antioxidante, tais como: ácido ascórbico e naringenina. Diante disso, para a produção do rGO, foram preparadas amostras de óxido de grafeno (GO) com suco de laranjapera in natura e processado, bem como a mistura dos dois sucos (in natura e processado) e da naringenina. Em etapa posterior, essas amostras foram submetidas à redução termoquímica. Por fim, realizou-se uma análise de microscopia eletrônica de varredura (MEV) com intuito de analisar a morfologia e microestrutura do rGO obtido, permitindo, assim, inferir sobre a efetividade do processo de redução, revelando que essa rota sustentável é viável para a obtenção do óxido de grafeno reduzido.