The aim of this report is to examine performance trends for Aerospikes and Supersonic nozzles with center – bodies. The initial case that was tested is a convergent – divergent conical nozzle with a geometry and inlet flow conditions obtained from a NASA technical note. The technical note mentions that air was used as the working fluid for the nozzle. This case served as the base case for comparison with the performance of later nozzle designs. Nozzle flow for all the cases that were tested was simulated using ANSYS Fluent, for ambient conditions at 20km standard atmosphere. The convergent – divergent conical nozzle has the following calculated performance parameters using results from ANSYS Fluent: mass flow rate of 9.660 kg/s, axial Thrust of 10,583.5 N, and a specific impulse of 111.7s. All of the Supersonic nozzles with center – bodies have calculated specific impulse values lower than 111.7s by 0.4 – 1.6s, for approximately the same calculated mass flow rates as the base case. Adding a center – body to the original conical nozzle, was simply detrimental to performance. With regards to the Aerospike nozzles, 18 of them were tested. Aerospike 18 has the highest calculated specific impulse, at 115.3s for a calculated mass flow rate of 9.671kg/s. Aerospike 13 came in second at 114.6s, for a calculated mass flow rate of 9.676 kg/s. Several of the Aerospike designs did not out-perform the base case in terms of specific impulse. For those Aerospikes, the convergent – divergent section had a significantly lower thrust than the base case and the center – body was not able to over-compensate for the lower thrust. This report also looks at trends in thrust contribution by the convergent – divergent sections and center – bodies of Aerospikes at different nozzle geometries. The working fluid for all the cases tested in ANSYS Fluent including the base case, is air at a ratio of specific heats equal to 1.4.
The aim of this report is to examine performance trends for Aerospikes and Supersonic nozzles with center – bodies. The initial case that was tested is a convergent – divergent conical nozzle with a geometry and inlet flow conditions obtained from a NASA technical note. The technical note mentions that air was used as the working fluid for the nozzle. This case served as the base case for comparison with the performance of later nozzle designs. Nozzle flow for all the cases that were tested was simulated using ANSYS Fluent, for ambient conditions at 20km standard atmosphere. The convergent – divergent conical nozzle has the following calculated performance parameters using results from ANSYS Fluent: mass flow rate of 9.660 kg/s, axial Thrust of 10,583.5 N, and a specific impulse of 111.7s. All of the Supersonic nozzles with center – bodies have calculated specific impulse values lower than 111.7s by 0.4 – 1.6s, for approximately the same calculated mass flow rates as the base case. Adding a center – body to the original conical nozzle, was simply detrimental to performance. With regards to the Aerospike nozzles, 18 of them were tested. Aerospike 18 has the highest calculated specific impulse, at 115.3s for a calculated mass flow rate of 9.671kg/s. Aerospike 13 came in second at 114.6s, for a calculated mass flow rate of 9.676 kg/s. Several of the Aerospike designs did not out-perform the base case in terms of specific impulse. For those Aerospikes, the convergent – divergent section had a significantly lower thrust than the base case and the center – body was not able to over-compensate for the lower thrust. This report also looks at trends in thrust contribution by the convergent – divergent sections and center – bodies of Aerospikes at different nozzle geometries. The working fluid for all the cases tested in ANSYS Fluent including the base case, is air at a ratio of specific heats equal to 1.4.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.