No abstract

No abstract

Hydrophobically associating block copolymers of polyacrylamide/styrene with a high hydrophobe content were synthesized using micellar copolymerization under various conditions of surfactant and initiator concentrations with the objective of determining the conditions that produce optimum solution properties for enhanced oil recovery. Solubilities, aqueous solution viscosities and interfacial properties with air and oil of the copolymers were investigated. The influence of salt on the solution properties was also studied. Nature of hydrophobic sites and onset of hydrophobic association were studied by measuring the fluorescence of pyrene in polymer solutions. Optimum solution properties were obtained for copolymers synthesized under conditions of high surfactant and initiator concentrations. The copolymers displayed substantial thickening properties at low concentrations with enhanced thickening in the presence of salt. The interfacial tensions of the aqueous solutions with n‐decane and air were also reduced. Interfacial properties were slightly sensitive to salt concentration. The copolymer solutions showed shear and temperature thinning behaviors typical of polymer solutions.

A B S T R A C TThe present study addresses the application of raw and modified carbon nanotubes (CNTs) and activated carbon (AC) for the removal of hexavalent chromium (Cr(VI)) from aqueous solution. Surfaces of both the adsorbents were modified by acid treatment. Nitric acid was used to remove impurities and to introduce carboxylic functional groups on the surfaces of CNTs and AC. Raw and modified adsorbents (CNTs and AC) were characterized by scanning electron microscopy, Brunauer-Emmett-Teller surface area analysis, and thermogravimetric analysis. The influence of adsorbent dosage, contact time, agitation speed, and solution pH were evaluated on the Cr(VI) removal efficiency using batch adsorption experiments. The optimum pH for maximum adsorption of Cr(VI) was found to be 3 and 4 for AC and CNTs, respectively. Modified and raw AC were able to remove 99 and 92% of Cr(VI) ions, respectively, at 75 mg adsorbent dosage, agitation speed of 200 rpm, initial Cr(VI) concentration of 1 mg/L, contact time of 4 h, and solution pH 3, while the removal of Cr(VI) ions recorded maximum values of 87 and 80% for modified and raw CNTs under same treatment conditions. However, acid modification of CNTs was found to have no major effect on the percentage removal of Cr(VI) ions at low adsorbent dosage. Adsorption capacities of both the adsorbents were determined using batch adsorption experiments and experimental data were described by Langmuir and Freundlich adsorption isotherm models. However, Langmuir isotherm model was able to best describe the adsorption of Cr(VI) ions on raw and modified forms of CNTs and AC. Maximum adsorption capacity (q e ) was found to be 2.024 and 1.805 mg/g for raw and modified AC, while 1.021 and 0.964 mg/g for raw and modified CNTs.

No abstract

The effect of pH and salt concentration on the partitioning behavior of bovine serum albumin (BSA) and cytochrome c in an aqueous two-phase polymer system containing a novel pH-responsive copolymer that mimics the structure of proteins and poly(ethylene glycol) (PEG) was investigated. The two-phase system has low viscosity. Depending on pH and salt concentration, the cytochrome c was found to preferentially partition into the pH-responsive copolymer-rich (bottom) phase under all conditions of pH and salt concentrations considered in the study. This was caused by the attraction between the positively charged protein and negatively charged copolymer. BSA partitioning showed a more complex behavior and partitioned either to the PEG phase or copolymer phase depending on the pH and ionic strength. Extremely high partitioning levels (partition coefficient of 0.004) and very high separation ratios of the two proteins (up to 48) were recorded in the new systems. This was attributed to strong electrostatic interactions between the proteins and the charged copolymer.

Summary: We used the dissipative particle dynamics method to simulate the self‐assembly of symmetric triblock copolymers of the type ABA. Depending on the volume fraction of the end blocks fA, several mesophases including lamellar, perforated lamellar, gyroid, hexagonal cylinders and bcc spherical micelles were obtained. The order‐disorder transition (ODT) at fA = 0.5 was found to be about χN = 19.8. The ODT for the cylindrical mesophase at symmetrical points on the phase diagram had different values, indicating asymmetry in the phase diagram. We were also able to estimate the bridge fraction in the different mesophases. They range from about 0.44 for the lamellar mesophase to about 0.75 for the spherical micelles. Our simulation results are in good agreement with previously reported theoretical calculations and experimental observations.

ABSTRACT:Composites of palm fibers and poly(propylene) (PP) were compounded in an extruder at 200°C. The composites were subsequently injection molded into standard tensile specimens for mechanical characterization. The fracture morphology of the specimens was analyzed by scanning electron microscopy. It was observed that the composite modulus increased with the increase of fiber content, indicating the existence of adhesion between PP and the much stiffer palm fibers. However, the adhesion was not satisfactory and resulted in a decrease in the composite tensile strength with fiber addition. The compatibilizer Epolene E-43 was used to minimize this incompatibility between the wood fibers and the PP matrix. The maleated PP additive enhanced the fiber-matrix adhesion, resulting in an improvement in composite performance. Also, small fibers showed better mechanical properties than those of long fibers.