Context. Optical long-baseline interferometry is moving a crucial step forward with the advent of general-user scientific instruments that equip large aperture and hectometric baseline facilities, such as the Very Large Telescope Interferometer (VLTI). Aims. AMBER is one of the VLTI instruments that combines up to three beams with low, moderate and high spectral resolutions in order to provide milli-arcsecond spatial resolution for compact astrophysical sources in the near-infrared wavelength domain. Its main specifications are based on three key programs on young stellar objects, active galactic nuclei central regions, masses, and spectra of hot extra-solar planets. Methods. These key science goals led to scientific specifications, which were used to propose and then validate the instrument concept. AMBER uses single-mode fibers to filter the entrance signal and to reach highly accurate, multiaxial three-beam combination, yielding three baselines and a closure phase, three spectral dispersive elements, and specific self-calibration procedures. Results. The AMBER measurements yield spectrally dispersed calibrated visibilities, color-differential complex visibilities, and a closure phase allows astronomers to contemplate rudimentary imaging and highly accurate visibility and phase differential measurements. AMBER was installed in 2004 at the Paranal Observatory. We describe here the present implementation of the instrument in the configuration with which the astronomical community can access it. Conclusions. After two years of commissioning tests and preliminary observations, AMBER has produced its first refereed publications, allowing assessment of its scientific potential.

Aims. In this paper, we present an innovative data reduction method for single-mode interferometry. It has been specifically developed for the AMBER instrument, the three-beam combiner of the Very Large Telescope Interferometer, but it can be derived for any single-mode interferometer. Methods. The algorithm is based on a direct modelling of the fringes in the detector plane. As such, it requires a preliminary calibration of the instrument in order to obtain the calibration matrix that builds the linear relationship between the interferogram and the interferometric observable, which is the complex visibility. Once the calibration procedure has been performed, the signal processing appears to be a classical least-square determination of a linear inverse problem. From the estimated complex visibility, we derive the squared visibility, the closure phase, and the spectral differential phase. Results. The data reduction procedures have been gathered into the so-called amdlib software, now available for the community, and are presented in this paper. Furthermore, each step in this original algorithm is illustrated and discussed from various on-sky observations conducted with the VLTI, with a focus on the control of the data quality and the effective execution of the data reduction procedures. We point out the present limited performances of the instrument due to VLTI instrumental vibrations which are difficult to calibrate.

Abstract. The young stellar object MWC 297 is an embedded B1.5Ve star exhibiting strong hydrogen emission lines and a strong near-infrared continuum excess. This object has been observed with the VLT interferometer equipped with the AMBER instrument during its first commissioning run. VLTI/AMBER is currently the only near infrared interferometer which can observe spectrally dispersed visibilities. MWC 297 has been spatially resolved in the continuum with a visibility of 0.50 +0.08 −0.10 as well as in the Brγ emission line where the visibility decrease to a lower value of 0.33 ± 0.06. This change in the visibility with the wavelength can be interpreted by the presence of an optically thick disk responsible for the visibility in the continuum and of a stellar wind traced by the Brγ emission line and whose apparent size is 40% larger. We validate this interpretation by building a model of the stellar environment that combines a geometrically thin, optically thick accretion disk model consisting of gas and dust, and a latitude-dependent stellar wind outflowing above the disk surface. The continuum emission and visibilities obtained from this model are fully consistent with the interferometric AMBER data. They agree also with existing optical, near-infrared spectra and other broad-band near-infrared interferometric visibilities. We also reproduce the shape of the visibilities in the Brγ line as well as the profile of this line obtained at an higher spectral resolution with the VLT/ISAAC spectrograph, and those of the Hα and Hβ lines. The disk and wind models yield a consistent inclination of the system of approximately 20• . A picture emerges in which MWC 297 is surrounded by an equatorial flat disk that is possibly still accreting and an outflowing wind which has a much higher velocity in the polar region than at the equator. The VLTI/AMBER unique capability to measure spectral visibilities therefore allows us for the first time to compare the apparent geometry of a wind with the disk structure in a young stellar system.

We report the fabrication of single mode buried channel waveguides for the whole mid-infrared transparency range of chalcogenide sulphide glasses (λ ≤ 11 µm), by means of direct laser writing. We have explored the potential of this technology by fabricating a prototype three-dimensional three-beam combiner for future application in stellar interferometry, which delivers a monochromatic interference visibility of 99.89% at 10.6 µm, and an ultrahigh bandwidth (3-11 µm) interference visibility of 21.3%. These results demonstrate that it is possible to harness the whole transparency range offered by chalcogenide glasses on a single on-chip instrument by means of direct laser writing, a finding that may be of key significance in future technologies such as astrophotonics and biochemical sensing. . An essential step in order to unleash all of this potential science is to develop integrated optical platforms capable of addressing the technological requirements that each field demands. In this sense, the development of on-chip instruments such as optical sensors, high resolution spectrometers, or sophisticated beam combiners, is currently of high interest for the previous mentioned applications [1,2,5,6,7].Although several MIR two-dimensional (2D) planar schemes have been recently developed [8,9], these are all based on multiple-step surface deposition and processing techniques, which place inherent limits to the device design and capabilities. In this Letter, we report the single-step fabrication of three-dimensional (3D) MIR photonic circuits inside chalcogenide glass, by means of ultrashort-pulse direct laser writing (DLW) [10][11][12][13][14]. We show that the MIR waveguide cores can be tailored in both size and refractive index, and can also be spatially positioned at will inside the material, making the chip extremely robust against mechanical stress, vibrations, humidity, and temperature changes [11]. Moreover, we also evidence that the useful range of these DLW waveguides is, as suspected [12], ultimately limited by the transparency range of the material used, and not by the fabrication technique.In this work, high quality research and commercial chalcogenide sulphide glasses were used, both of which are free of highly toxic arsenic compounds. These glasses were commercial GaLaS (here after GLS) [14] and the research composition 75GeS2-15Ga2S3-4CsI-2Sb2S3-4SnS (here after GCIS) [15]. The MIR transmission upper limit of commercial GLS is known to be ~10 µm [14], while for GCIS we measured a slightly higher transmission upper limit of ~11 µm, as it is shown in Figure 1(a).