We report here, for the first time, the role of the molecular design on the liquid crystalline and solid-state photoluminescent properties of soluble and thermally stable liquid crystalline perylenebisimide derivatives. A new series of perylenebisimides were designed and developed for this purpose by adopting the stoichiometry-control approach, and amine-, hydroxyl-, ester-, and amide-functionalized molecules were synthesized. Various types of spacers with different lengths (C(2) to C(12)), types (linear, cyclohexyl, and tricyclodecane), and end-capped by phenyl or tridodecyloxy gallic units were introduced in the perylenebisimide core. The molecules were completely characterized by NMR, FT-IR, SEC, and MALDI-TOF mass techniques. Thermal analysis revealed that the perylenebisimide derivatives were thermotropic liquid crystalline, and threadlike nematic phases were observed under a polarizing light microscope. The spacer length and the rigidity of the spacers play a major role in the liquid crystalline properties of the materials. In phenyl systems, the C(6) chain with ester- and the C(12) chain with amide-end-capped molecules showed a nematic phase, whereas the C(6) chain with an amide end cap and their cyclic and tricyclic counterparts did not show any LC property. The introduction of a tridodecyloxy gallic unit induced the LC property in C(12) and the cyclohexyl system; however, it failed to do so in the tricyclodecane molecule. The absorption properties of the molecules were almost unchanged by the structural variation; however, the emission quantum yield in solution and photoluminescent (PL) intensity in the solid state were significantly different. Though the gallic unit induced liquid crystallinity in the perylenebisimide core, the quantum yield and PL intensity are 4-5 times less compared to those of the simple phenyl-capped liquid crystalline system. Among the various types of spacers, the tricyclodecane induced strong molecular aggregates via pi-stacking, which in turn increased the rigidity of the entire perylenebisimide core, resulting in the absence of liquid crystallinity and low luminescence compared to their linear and cyclohexyl analogues. The molecular aggregates were very stable even at very dilute concentration and also at high temperatures. The aggregates disappeared immediately upon addition of trifluoroacetic acid, thus confirming the strong hydrogen bonding in the aggregated states. In a nutshell, the present report demonstrates the importance of molecular design for introducing liquid crystalline phases in perylenebisimides and also the development of novel highly luminescent n-type pi-conjugated material for application in optoelectronics.

Here we report, for the first time, a novel molecular design for three-dimensional honeycomb structures through a self-organization of hydrogen-bonded bulky anchoring group in a methacrylic polymer backbone. The polymerizable monomer design includes a methacrylic double bond linked to various hydrophobic anchoring units such as ethane, n-decane, tricyclodecane (TCD), and adamantane via a hydrogen-bonded cycloaliphatic urethane linkage. The structures of the polymers were confirmed by nuclear magnetic resonance (NMR) and the molecular weights of the polymer were determined by gel permeation chromatography (GPC). The methacrylate polymers having tricyclodecane and adamantane bulky anchoring groups self-organized to produce three-dimensional honeycomb patterns in tetrahydrofuran-water solvent mixture at ambient conditions, whereas its linear analogues (ethane, n-decane) failed to produce any micropattern. The scanning electron microscopy (SEM) analysis of the above-prepared polymer films revealed that the structure of the polymer played a major role in the formation of the honeycomb patterns. The solution Fourier transform infrared (FTIR) measurements confirmed that the bulky tricyclodecane and adamantane polymers have strong hydrogen-bonding interaction compared to that of their linear analogues, which is the driving force for the micropatterns. Transmission electron microscopy (TEM) and atomic force microscopy (AFM) analysis of the bulky polymers revealed that the polymers exist as vesicles or micelles in the solution, which leads to the formation of the honeycomb pattern. The honeycomb pattern formation in the bulky polymer systems suggests that two cooperative factors such as hydrogen-bonding interaction and hydrophobicity of bulky anchoring units are necessary to induce three-dimensional honeycomb structures. To investigate the effect of molecular weights and its distribution on the self-organization process, both benzoyl peroxide (BPO) initiated free radical and atom transfer radical polymerization (ATRP) techniques were employed for the polymerization. Micropores formed irrespective of differences in molecular weight and polydispersity index (PDI); however, the pore size distribution was influenced by both molecular weights and PDI. Low molecular weight samples afforded polydisperse pores with the ATRP samples with more narrow PDI producing pores with large dimensions. The approach has also been investigated for polystyrene-bulky methacrylic copolymer, and the results revealed that uniform honeycomb patterns were produced for copolymers having more than 50 mol % incorporation of bulky units.

Homochiral mesoporous anodic aluminum oxide membranes (AAO) were prepared by coating protected chiral D/L aspartic acid appended polyfluorene in the pores. These chiral AAO membranes successfully demonstrated enantioselective recognition and separation of a range of amino acids from their aqueous racemic mixture by simple filtration. Enantioselective separation was achieved by selective adsorption of one enantiomer from the aqueous racemic mixture into the chiral pores of the AAO membrane leaving the filtrate enriched with the other enantiomer. Extraction and quantification of the adsorbed amino acid (glutamic acid) demonstrated that 1 mg of homochiral polyfluorene could effectively extract about 3.5 mg of glutamic acid with 95% enantiomeric excess in 24 h. This is one of the highest enantiomeric excesses (ee %) and yields reported so far in the literature for a racemic mixture of glutamic acid. The pore size of the AAO membrane influenced the efficiency of separation with a reduction in pore size from 200 to 20 nm leading to reduced ee % (∼95% to ∼28%). These results raise the possibility for a facile method to carry out enantioselective separation.