Bioartificial blends of poly-(epsilon-caprolactone) (PCL) with a polysaccharide (starch, S; dextran, D; or gellan, G) (PCL/S, PCL/D, PCL/G 90.9/9.1 wt ratio) were prepared by a solution-precipitation technique and widely characterized by differential scanning calorimetry analysis (DSC), Fourier transform infrared-attenuated total reflectance spectroscopy (FTIR-ATR), optical microscopy (OM), wide-angle X-ray diffraction analysis (WAXD), and thermogravimetry (TGA). DSC showed that the polysaccharide reduced the crystallinity of PCL and had a nucleation effect, which was also confirmed by OM analysis. Hoffman-Weeks analysis was performed on PCL and blend samples allowing calculation of their equilibrium melting temperatures (). WAXD showed that the crystalline unit cell type was the same for PCL and blends. FTIR-ATR did not evidence interactions between blend components. Thermal stability was affected by the type of polysaccharide. Microparticles (<125 microm) were produced from blends by cryogenical milling and characterized by scanning electron microscopy analysis (SEM). Selective laser sintering (SLS), a new rapid prototyping technology for scaffold fabrication, was applied to sinter blend microparticles according to a PC-designed two-dimensional geometry (strips and 2 x 2 mm(2) square-meshed grids). The optimal experimental conditions for sintering were established and laser beam parameters (beam speed, BS, and power, P) were found for each blend composition. Morphology of sintered objects was analyzed by SEM and found to be dependent on the morphology of the sintered powders. Sintered samples were analyzed by chemical imaging (CI), FTIR-ATR, DSC, and contact angle analysis. No evidence of the occurrence of degradation phenomena was found by FTIR-ATR for sintered samples, whereas DSC parameters of PCL and blends showed changes which could be attributed to some molecular weight decrease of PCL during sintering. CI of sintered samples showed that the polysaccharide phase was homogeneously dispersed within the PCL matrix, with the only exception being the PCL/D blend. The contact angle analysis showed that all samples were hydrophilic. Fibroblasts were then seeded on scaffolds to evaluate the rate and the extent of cell adhesion and the effect of the polysaccharides (S, D, G) on the bioactivity of the PCL-based blends.

No abstract

Blends between chitosan (CS) and gelatin (G) with various compositions (CS/G 0/100 20/80, 40/60, 60/40 100/0 w/w) were produced, as candidate materials for biomedical applications. Different amounts of genipin (0.5 wt.% and 2.5 wt.%) were used to crosslink CS/G blends, promoting the formation of amide and tertiary amine bonds between the macromolecules and the crosslinker. The effects of composition and crosslinking on the physico-chemical properties of samples were evaluated by infrared analysis, thermogravimetry, contact angle measurements, dissolution and swelling tests. Mechanical properties of crosslinked samples were also determined through stress-strain and creep tests: samples stiffness increased with increasing the crosslinker amount and the CS content. Blend composition affected mouse fibroblasts adhesion and proliferation on substrates, depending on the crosslinker amount. Finally, crosslinked CS/G blends containing 80 wt.% G were found to support neuroblastoma cells adhesion and proliferation which made them promising candidates for uses in the field of nerve regeneration.

A technique for controlled deposition of biomaterials and cells in specific and complex architectures is described. It employs a highly accurate three-dimensional micropositioning system with a pressure-controlled syringe to deposit biopolymer structures with a lateral resolution of 5 microm. The pressure-activated microsyringe is equipped with a fine-bore exit needle and a wide variety of two- and three-dimensional patterns on which cells to be deposited can adhere. The system has been characterized in terms of deposition parameters such as applied pressure, motor speed, line width and height, and polymer viscosity, and a fluid dynamic model simulating the deposition process has been developed, allowing an accurate prediction of the topological characteristics of the polymer structures.

The replacement of injured cardiac contractile cells with stem cell-derived functionally efficient cardiomyocytes has been envisaged as the resolutive treatment for degenerative heart diseases. Nevertheless, many technical issues concerning the optimal procedures to differentiate and engraft stem cells remain to be answered before heart cell therapy could be routinely used in clinical practice. So far, most studies have been focused on evaluating the differentiative potential of different growth factors without considering that only the synergistic cooperation of biochemical, topographic, chemical, and physical factors could induce stem cells to adopt the desired phenotype. The present study demonstrates that the differentiation of cardiac progenitor cells to cardiomyocytes does not occur when cells are challenged with soluble growth factors alone, but requires strictly controlled procedures for the isolation of a progenitor cell population and the artifactual recreation of a microenvironment critically featured by a fine-tuned combination of specific biological and physical factors. Indeed, the scaffold geometry and stiffness are crucial in enhancing growth factor differentiative effects on progenitor cells. The exploitation of this concept could be essential in setting up suitable procedures to fabricate functionally efficient engineered tissues.

Human midbrain-specific organoids (hMOs) serve as an experimental in vitro model for studying the pathogenesis of Parkinson's disease (PD). In hMOs, neuroepithelial stem cells (NESCs) give rise to functional midbrain dopaminergic (mDA) neurons that are selectively degenerating during PD. A limitation of the hMO model is an under-supply of oxygen and nutrients to the densely packed core region, which leads eventually to a "dead core". To reduce this phenomenon, we applied a millifluidic culture system that ensures media supply by continuous laminar flow. We developed a computational model of oxygen transport and consumption in order to predict oxygen levels within the hMOs. The modelling predicts higher oxygen levels in the hMO core region under millifluidic conditions. In agreement with the computational model, a significantly smaller "dead core" was observed in hMOs cultured in a bioreactor system compared to those ones kept under conventional shaking conditions. Comparing the necrotic core regions in the organoids with those obtained from the model allowed an estimation of the critical oxygen concentration necessary for ensuring cell vitality. Besides the reduced "dead core" size, the differentiation efficiency from NESCs to mDA neurons was elevated in hMOs exposed to medium flow. Increased differentiation involved a metabolic maturation process that was further developed in the millifluidic culture. Overall, bioreactor conditions that improve hMO quality are worth considering in the context of advanced PD modelling.

The physiological environment of the intestine is characterized by its variegated composition, numerous functions and unique dynamic conditions, making it challenging to recreate the organ in vitro . This review outlines the requirements for engineering physiologically relevant intestinal in vitro models, mainly focusing on the importance of the mechano-structural cues that are often neglected in classic cell culture systems. More precisely: the topography, motility and flow present in the intestinal epithelium. After defining quantitative descriptors for these features, we describe the current state of the art, citing relevant approaches used to address one (or more) of the elements in question, pursuing a progressive conceptual construction of an “ideal” biomimetic intestinal model. The review concludes with a critical assessment of the currently available methods to summarize the important features of the intestinal tissue in the light of their different applications.

Abstract:In this paper, we discuss the basic design requirements for the development of physiologically meaningful in vitro systems comprising cells, scaffolds and bioreactors, through a bottom up approach. Very simple micro-and milli-fluidic geometries are first used to illustrate the concepts, followed by a real device case-study. At each step, the fluidic and mass transport parameters in biological tissue design are considered, starting from basic questions such as the minimum number of cells and cell density required to represent a physiological system and the conditions necessary to ensure an adequate nutrient supply to tissues. At the next level, we consider the use of three-dimensional scaffolds, which are employed both for regenerative medicine applications and for the study of cells in environments which better recapitulate the physiological milieu. Here, the driving need is the rate of oxygen supply which must be maintained at an appropriate level to ensure cell viability throughout the thickness of a scaffold. Scaffold and bioreactor design are both critical in defining the oxygen profile in a cell construct and are considered together. We also discuss the oxygen-shear stress trade-off by considering the levels of mechanical stress required for hepatocytes, which are the limiting cell type in a multi-organ model. Similar considerations are also made for glucose consumption in cell constructs. Finally, the allometric approach for generating multi-tissue systemic models using bioreactors is described.